Husqvarna P 520D, P 525D manual Driving the Rider, Braking, Stop the engine

Page 19

DRIVING

Driving the Rider

1 Release the parking brake before driving

2Carefully press down one of the pedals until the required speed is obtained. Pedal (1) is used to drive forwards, and pedal (2) to drive backwards.

1

2

3Lower the cutting unit by directly moving the lever forward to the ﬂoat position where the lever stays put.

4Start the cutting unit if necessary by pulling up the switch for the cutting unit.

Braking

Release the drive pedals. The machine slows and is stopped by the drive system. Do not use the parking brake as the drive brake.

Quicker braking is possible if you press down the drive pedal for the opposite direction.

Stop the engine

Preferably allow the engine to idle for a minute to obtain normal working temperature before stopping it if it has been working hard.

Turn off the cutting unit using the PTO button.

1 Apply the parking brake by moving the handle downward.

2 Lift the cutting unit with the hydraulic lifting lever.

3Move the throttle control to the MIN. position. Turn the ignition key to ”OFF”-position.

English – 19

Image 19

Contents English 520D 525DContents After the ﬁrst 25 hours Pre-delivery serviceTowing IntroductionDear Customer Driving and transport on public roadsGood service Symbols KEY to SymbolsLocation of the controls What is WHAT?General use Safety InstructionsSafety instructions Insure your RiderThis is what you do Driving on slopesChildren MaintenanceTransport Presentation Lowering the Unit Mowing Position Adjusting the cutting heightLever for hydraulic lift of attachments Lifting the Cutting Unit Transport PositionFueling Lights and power outletSafety instructions SeatBypass valves Instrument panelAuxiliary lift system Rops Roll Over Protective StructureStart the engine Starting and driving when coldStarting Engine Before startingConnecting the jump leads Starting the engine with a weak batteryRemove the cables in the reverse order Stop the engine DrivingDriving the Rider BrakingOther objects which can be thrown out by the blades Cutting tips800 Maintenance scheduleStarting Completed Removing of the machine hoods CleaningChecking the engine’s cooling air intake Change pump and alternator belt Adjustment of pump and alternator beltAdjusting the parking brake Replacement of fuel ﬁlterReplacing the air ﬁlter Cleaning the air ﬁlterCleaning the engine and mufﬂer Cleaning the ﬁlter coverChecking the tyre pressure Check the safety systemReplacing the light bulbs Main fuseCutting Unit Components Check the batteryFitting the cutting head Trapping your hand Pins are loosened. Observe caution to avoidRemoving the cutting unit Lift arms move with great force whenPlacing in the service position Service position for the cutting unitRestoring from service position Cutting height and tilt angle adjustmentCutting height Tilt angle Replacing the cutting unit beltsChecking the blades Removing the BioClip plugChange PTO belts Adjustment of PTO beltsGlycol Water Freezing point Change coolantGeneral Lubrication scheduleUniversal drive shaft joints AccessoriesPivot wheel bearings Cutting unit bevel gearJoint bearing Drive shaft front support bearingDrive shaft rear support bearing Steering cylinderDrained directly after stopping the engine Changing the oil ﬁlterCheck the hydraulic system oil level Replacing the engine oilLubricating the cables Knobs for setting the cutting heightLubricate the parking brake wire Driver seatEngine does not run smoothly Problem Procedure Engine does not startEngine seems to have no power Starter motor does not turn over the engineEngine overheats Battery does not chargeUneven mowing Electrical System Wiring diagram P 520D Electrical System Electrical System Electrical System Electrical System Electrical System Wiring diagram P525 D Electrical System Electrical System Electrical System Electrical System Electrical System Winter storage ServiceGuard Technical Data Sound levels see note EC-declaration of conformity Applies to Europe onlyVibration levels see note Original instructions 1154837-26 ´z+Vsh¶6¨ ´z+Vsh¶6¨