Husqvarna P 520D, P 525D manual Transport

Page 11

SAFETY INSTRUCTIONS

•Stop and inspect the equipment if you run over or into anything. If necessary, make repairs before starting.

•Never make adjustments with the engine running.

•The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer.

•The blades are sharp and can cause cuts. Wrap the blades or wear protective gloves when handling them.

•Check regularly that the parking brake works. Adjust and maintain as required.

•Reduce the risk of ﬁre by removing grass, leaves and other debris that may have fastened on the machine. Allow the machine to cool before putting it in storage.

Transport

IMPORTANT INFORMATION

The parking brake is not sufﬁcient to lock the machine during transport. Ensure you secure the machine ﬁrmly to the transporting vehicle.

•The machine is heavy and can cause serious crush injuries. Take extra care when loading it onto or off a vehicle or trailer.

•Use an approved trailer to transport the machine.

•To secure the machine on the trailer, two approved tension belts and four wedge shaped wheel blocks should be used.

Engage the parking brake and tie the tension belts around the front and rear brackets.

Secure the machine by tensioning the belts towards the back and the front of the trailer respectively.

Place the wheel blocks in front of and behind the rear wheels.

•Check and observe local road trafﬁc regulations before transporting or driving the machine on roads.

English – 11

Image 11

Contents English 520D 525DContents After the ﬁrst 25 hours Pre-delivery serviceTowing IntroductionDear Customer Driving and transport on public roadsGood service Symbols KEY to SymbolsLocation of the controls What is WHAT?General use Safety InstructionsSafety instructions Insure your RiderThis is what you do Driving on slopesChildren MaintenanceTransport Presentation Lowering the Unit Mowing Position Adjusting the cutting heightLever for hydraulic lift of attachments Lifting the Cutting Unit Transport PositionFueling Lights and power outletSafety instructions SeatBypass valves Instrument panelAuxiliary lift system Rops Roll Over Protective StructureStart the engine Starting and driving when coldStarting Engine Before startingRemove the cables in the reverse order Starting the engine with a weak batteryConnecting the jump leads Stop the engine DrivingDriving the Rider BrakingOther objects which can be thrown out by the blades Cutting tipsStarting Completed Maintenance schedule800 Checking the engine’s cooling air intake CleaningRemoving of the machine hoods Change pump and alternator belt Adjustment of pump and alternator beltAdjusting the parking brake Replacement of fuel ﬁlterReplacing the air ﬁlter Cleaning the air ﬁlterCleaning the engine and mufﬂer Cleaning the ﬁlter coverChecking the tyre pressure Check the safety systemReplacing the light bulbs Main fuseFitting the cutting head Check the batteryCutting Unit Components Trapping your hand Pins are loosened. Observe caution to avoidRemoving the cutting unit Lift arms move with great force whenPlacing in the service position Service position for the cutting unitCutting height Cutting height and tilt angle adjustmentRestoring from service position Tilt angle Replacing the cutting unit beltsChecking the blades Removing the BioClip plugChange PTO belts Adjustment of PTO beltsGlycol Water Freezing point Change coolantGeneral Lubrication scheduleUniversal drive shaft joints AccessoriesPivot wheel bearings Cutting unit bevel gearJoint bearing Drive shaft front support bearingDrive shaft rear support bearing Steering cylinderDrained directly after stopping the engine Changing the oil ﬁlterCheck the hydraulic system oil level Replacing the engine oilLubricating the cables Knobs for setting the cutting heightLubricate the parking brake wire Driver seatEngine does not run smoothly Problem Procedure Engine does not startEngine seems to have no power Starter motor does not turn over the engineUneven mowing Battery does not chargeEngine overheats Electrical System Wiring diagram P 520D Electrical System Electrical System Electrical System Electrical System Electrical System Wiring diagram P525 D Electrical System Electrical System Electrical System Electrical System Electrical System Guard ServiceWinter storage Technical Data Vibration levels see note EC-declaration of conformity Applies to Europe onlySound levels see note Original instructions 1154837-26 ´z+Vsh¶6¨ ´z+Vsh¶6¨