Husqvarna P 520D manual Knobs for setting the cutting height, Driver seat, Lubricating the cables

Page 37

Lubrication

Check the oil level in the transmission gearboxes

•Use the oil dipstick to check that there is oil in the transmission.

•The oil level should be between the markings on the dipstick.

•Reﬁll as required with fully synthetic 10W/50 API SM oil or better

Knobs for setting the cutting height

Lubricate front and rear knobs with oil.

Driver seat

Fold up the seat.

Lubricate the lever for longitudinal adjustment with oil.

Lubricate the longitudinal adjustment runners with grease. Pull the seat back and forth and lubricate on both sides.

Lubricating the cables

Remove the cable´s rubber casing when lubricating.

Grease both ends of the cables and move the controls to end stop positions when lubricating.

Re-attach the rubber covers on the cables after lubrication.

Cables with sheaths will jam if they are not lubricated regularly. A jammed cable may cause malfunction, such as the parking braking being applied. If a cable binds, remove the cable and hang it vertically. Lubricate it with thin engine oil until the oil begins to escape from the bottom.

A tip: Fill a small plastic bag with oil and tape it so that it seals against the casing and allow the cable to hang vertically from the bag overnight. If you do not succeed in lubricating the cable, it must be replaced.

Throttle and choke cables, lever bearings

•Remove the right side cover on the lever housing (3 screws) and open the engine cover.

•Lubricate the cables’ free ends with the oilcan, even those by the engine.

•Move the controls to the end points and lubricate again.

Replace the lever housing’s side cover.

Lubricate the parking brake wire

Remove the rubber cover and lubricate the cable with oil.

English – 37

Image 37

Contents English 520D 525DContents After the ﬁrst 25 hours Pre-delivery serviceDear Customer IntroductionDriving and transport on public roads TowingGood service Symbols KEY to SymbolsLocation of the controls What is WHAT?Safety instructions Safety InstructionsInsure your Rider General useThis is what you do Driving on slopesChildren MaintenanceTransport Presentation Lever for hydraulic lift of attachments Adjusting the cutting heightLifting the Cutting Unit Transport Position Lowering the Unit Mowing PositionSafety instructions Lights and power outletSeat FuelingBypass valves Instrument panelAuxiliary lift system Rops Roll Over Protective StructureStarting Engine Starting and driving when coldBefore starting Start the engineConnecting the jump leads Starting the engine with a weak batteryRemove the cables in the reverse order Driving the Rider DrivingBraking Stop the engineOther objects which can be thrown out by the blades Cutting tips800 Maintenance scheduleStarting Completed Removing of the machine hoods CleaningChecking the engine’s cooling air intake Adjusting the parking brake Adjustment of pump and alternator beltReplacement of fuel ﬁlter Change pump and alternator beltCleaning the engine and mufﬂer Cleaning the air ﬁlterCleaning the ﬁlter cover Replacing the air ﬁlterReplacing the light bulbs Check the safety systemMain fuse Checking the tyre pressureCutting Unit Components Check the batteryFitting the cutting head Removing the cutting unit Pins are loosened. Observe caution to avoidLift arms move with great force when Trapping your handPlacing in the service position Service position for the cutting unitRestoring from service position Cutting height and tilt angle adjustmentCutting height Checking the blades Replacing the cutting unit beltsRemoving the BioClip plug Tilt angleChange PTO belts Adjustment of PTO beltsGlycol Water Freezing point Change coolantGeneral Lubrication schedulePivot wheel bearings AccessoriesCutting unit bevel gear Universal drive shaft jointsDrive shaft rear support bearing Drive shaft front support bearingSteering cylinder Joint bearingCheck the hydraulic system oil level Changing the oil ﬁlterReplacing the engine oil Drained directly after stopping the engineLubricate the parking brake wire Knobs for setting the cutting heightDriver seat Lubricating the cablesEngine seems to have no power Problem Procedure Engine does not startStarter motor does not turn over the engine Engine does not run smoothlyEngine overheats Battery does not chargeUneven mowing Electrical System Wiring diagram P 520D Electrical System Electrical System Electrical System Electrical System Electrical System Wiring diagram P525 D Electrical System Electrical System Electrical System Electrical System Electrical System Winter storage ServiceGuard Technical Data Sound levels see note EC-declaration of conformity Applies to Europe onlyVibration levels see note Original instructions 1154837-26 ´z+Vsh¶6¨ ´z+Vsh¶6¨