Husqvarna P 525D, P 520D Check the battery, Cutting Unit Components, Fitting the cutting head

Page 26

Maintenance

Check the battery

WARNING! Lead-acid batteries produce

!explosive gases. Avoid sparks, open ﬂames and smoking close to batteries. Always wear protective glasses in the vicinity of batteries.

The machine is equipped with a maintenance-free battery. The battery has a service window showing different colours.

•White = Charge battery

•Green = OK.

•Red = Change battery.

Clean the battery and holder with soap/water solution.

A discarded or replacement battery should be handled as hazardous waste.

The Cutting Unit Components

The components mentioned are:

4

3

2

9

5

6

Fitting the cutting head

1Place the machine on a ﬂat surface and apply the parking brake.

2Start the engine and lower the lift arms to ﬂoating mode.

!	WARNING! If the help function is engaged,
	the lift arms will move with great force if
	someone releases the lifting lever. Observe
	caution to avoid trapping your hand.

Risk of crush injuries.

3Turn off the motor.

4Fit the universal drive shaft to the cutting unit. Slide the ring sideways to release the quick coupling and the universal drive shaft can be pushed onto the shaft pin.

8 7

1

4

5Make sure the rubber casing is folded over the front universal joint.

1Cotter pin

2Link joint

3Cutting unit bracket

4Clipping height adjusters

5Universal drive shaft with quick connectors

6Attachment point for service position

7Service strut

8Belt cover

9Gear

6Remove the bolts and pins from the link joint on the lift arms.

7Slide in the cutting unit so that the link joint aligns with the opening in the unit.

8Insert the bolts for the link joints and the pins on both sides.

26 – English

Image 26

Contents 520D 525D EnglishContents Pre-delivery service After the ﬁrst 25 hoursDriving and transport on public roads IntroductionDear Customer TowingGood service KEY to Symbols SymbolsWhat is WHAT? Location of the controlsInsure your Rider Safety InstructionsSafety instructions General useDriving on slopes This is what you doMaintenance ChildrenTransport Presentation Lifting the Cutting Unit Transport Position Adjusting the cutting heightLever for hydraulic lift of attachments Lowering the Unit Mowing PositionSeat Lights and power outletSafety instructions FuelingInstrument panel Bypass valvesRops Roll Over Protective Structure Auxiliary lift systemBefore starting Starting and driving when coldStarting Engine Start the engineRemove the cables in the reverse order Starting the engine with a weak batteryConnecting the jump leads Braking DrivingDriving the Rider Stop the engineCutting tips Other objects which can be thrown out by the bladesStarting Completed Maintenance schedule800 Checking the engine’s cooling air intake CleaningRemoving of the machine hoods Replacement of fuel ﬁlter Adjustment of pump and alternator beltAdjusting the parking brake Change pump and alternator beltCleaning the ﬁlter cover Cleaning the air ﬁlterCleaning the engine and mufﬂer Replacing the air ﬁlterMain fuse Check the safety systemReplacing the light bulbs Checking the tyre pressureFitting the cutting head Check the batteryCutting Unit Components Lift arms move with great force when Pins are loosened. Observe caution to avoidRemoving the cutting unit Trapping your handService position for the cutting unit Placing in the service positionCutting height Cutting height and tilt angle adjustmentRestoring from service position Removing the BioClip plug Replacing the cutting unit beltsChecking the blades Tilt angleAdjustment of PTO belts Change PTO beltsChange coolant Glycol Water Freezing pointLubrication schedule GeneralCutting unit bevel gear AccessoriesPivot wheel bearings Universal drive shaft jointsSteering cylinder Drive shaft front support bearingDrive shaft rear support bearing Joint bearingReplacing the engine oil Changing the oil ﬁlterCheck the hydraulic system oil level Drained directly after stopping the engineDriver seat Knobs for setting the cutting heightLubricate the parking brake wire Lubricating the cablesStarter motor does not turn over the engine Problem Procedure Engine does not startEngine seems to have no power Engine does not run smoothlyUneven mowing Battery does not chargeEngine overheats Electrical System Wiring diagram P 520D Electrical System Electrical System Electrical System Electrical System Electrical System Wiring diagram P525 D Electrical System Electrical System Electrical System Electrical System Electrical System Guard ServiceWinter storage Technical Data Vibration levels see note EC-declaration of conformity Applies to Europe onlySound levels see note 1154837-26 ´z+Vsh¶6¨ ´z+Vsh¶6¨ Original instructions