Husqvarna P 525D, P 520D manual Changing the oil filter, Check the hydraulic system oil level

Page 36

Lubrication

The following oil classes are recommended:

•API Service Class: CH4 or ACEA E5 or higher.

Choose an oil with viscosity according to the temperature ranges in the figure:

0W

5W 20

10W 30

15W 40

20W 50

20

30

40

-30

-20

-10

0

10

20

30

40

50 C

-22

-4

-14

32

50

68

86

104

122 F

Do not mix different types of oil.

Replacing the engine oil

Open the engine cover.

The engine oil should be changed the first time after 25 hours running time. It should then be changed after every 100 hours of running time.

WARNING! Engine oil can be very hot if it is

!drained directly after stopping the engine. Allow the engine to cool somewhat first.

1 Place a container underneath the engine oil drain plug.

2Remove the dipstick. Remove the drain plug from the engine.

3Let the oil run out into the container.

4Fit the drain plug and tighten it.

5Change oil filter if necessary.

6If necessary fill so that the oil comes up to the FULL mark on the dipstick.

7Run the engine warm, then check that there is no leakage from the oil plug.

8Check the engine oil level and top up if necessary.

IMPORTANT INFORMATION

Used engine oil, antifreeze etc. is a health hazard and must not be disposed of on the ground or in nature; it should always be disposed of at a workshop or appropriate disposal location.

Avoid skin contact; wash with soap and water in case of spills.

Changing the oil filter

!

WARNING! Engine oil can be very hot if it is

drained directly after stopping the engine.

Allow the engine to cool somewhat first.

The oil filter is located on the right side of the engine.

•Open the engine cover.

•Place a suitable vessel to collect the oil in.

•Turn the old oil filter anti-clockwise to remove. If necessary, use a filter remover.

•Clean the oil filter bracket.

•Lightly lubricate the rubber seal on the new oil filter using new oil.

•Fit the oil filter by turning clockwise. Turn by hand until the rubber seal is seated. Now tighten a further half turn.

•Start the engine and let it idle for about 3 minutes. Now stop it and check for signs of leakage.

•Check the engine oil level and top up if necessary.

IMPORTANT!

Used engine oil and transmission oil is hazardous to health and must not be disposed of in the ground or out of doors.

Replaced filters must be handed in to the workshop or other allotted place for disposal.

Avoid skin contact; wash with soap and water in case of spills.

Check the hydraulic system oil level

The oil and filter should be changed by an authorised service representative, as described in the Workshop Manual. Work on the system entails particular demands on cleanliness and the system must be vented before the machine is used.

•Fold up the seat.

•Remove the filler cap. The level should be 40-60 mm from the strainer top.

•Refill as required with fully synthetic 10W/50 API SM oil or better

36 – English

Page 35 Page 37
Image 36
Page 35 Page 37
Contents 520D 525D EnglishContents Pre-delivery service After the first 25 hoursIntroduction Dear CustomerDriving and transport on public roads TowingGood service KEY to Symbols SymbolsWhat is WHAT? Location of the controlsSafety Instructions Safety instructionsInsure your Rider General useDriving on slopes This is what you doMaintenance ChildrenTransport Presentation Adjusting the cutting height Lever for hydraulic lift of attachmentsLifting the Cutting Unit Transport Position Lowering the Unit Mowing PositionLights and power outlet Safety instructionsSeat FuelingInstrument panel Bypass valvesRops Roll Over Protective Structure Auxiliary lift systemStarting and driving when cold Starting EngineBefore starting Start the engineStarting the engine with a weak battery Connecting the jump leadsRemove the cables in the reverse order Driving Driving the RiderBraking Stop the engineCutting tips Other objects which can be thrown out by the bladesMaintenance schedule 800Starting Completed Cleaning Removing of the machine hoodsChecking the engine’s cooling air intake Adjustment of pump and alternator belt Adjusting the parking brakeReplacement of fuel filter Change pump and alternator beltCleaning the air filter Cleaning the engine and mufflerCleaning the filter cover Replacing the air filterCheck the safety system Replacing the light bulbsMain fuse Checking the tyre pressureCheck the battery Cutting Unit ComponentsFitting the cutting head Pins are loosened. Observe caution to avoid Removing the cutting unitLift arms move with great force when Trapping your handService position for the cutting unit Placing in the service positionCutting height and tilt angle adjustment Restoring from service positionCutting height Replacing the cutting unit belts Checking the bladesRemoving the BioClip plug Tilt angleAdjustment of PTO belts Change PTO beltsChange coolant Glycol Water Freezing pointLubrication schedule GeneralAccessories Pivot wheel bearingsCutting unit bevel gear Universal drive shaft jointsDrive shaft front support bearing Drive shaft rear support bearingSteering cylinder Joint bearingChanging the oil filter Check the hydraulic system oil levelReplacing the engine oil Drained directly after stopping the engineKnobs for setting the cutting height Lubricate the parking brake wireDriver seat Lubricating the cablesProblem Procedure Engine does not start Engine seems to have no powerStarter motor does not turn over the engine Engine does not run smoothlyBattery does not charge Engine overheatsUneven mowing Electrical System Wiring diagram P 520D Electrical System Electrical System Electrical System Electrical System Electrical System Wiring diagram P525 D Electrical System Electrical System Electrical System Electrical System Electrical System Service Winter storageGuard Technical Data EC-declaration of conformity Applies to Europe only Sound levels see noteVibration levels see note 1154837-26 ´z+Vsh¶6¨ ´z+Vsh¶6¨ Original instructions
Top Page Image Contents