Husqvarna P 520D Drive shaft front support bearing, Drive shaft rear support bearing, Link brace

Page 35

Lubrication

The drive shaft front support bearing

Lubricate with a grease gun until the grease is forced out.

The drive shaft rear support bearing

2 grease nipples. Lubricate with a grease gun until the grease is forced out.

Steering cylinder

The steering cylinder has two grease nipples, one on each end. Lubricate with a grease gun until the grease is forced out.

Joint bearing

Grease the waist section of joint bearing Lubricate with a grease gun until the grease is forced out.

Link brace

2 grease nipples, one on each side. Lubricate with a grease gun until the grease is forced out.

Checking the engine’s oil level.

Check the oil level in the engine when the Rider stands horizontal with the engine switched off.

Open the engine cover.

Loosen the dipstick, pull it up and wipe it off.

Now insert the dipstick again.

Pull the dipstick out again and read the oil level.

The oil level should be between the markings on the dipstick. If the level is approaching the ADD mark, top up the oil to the FULL mark on the dipstick.

The oil filler is on the valve cap. Fill the oil slowly.

Tighten the dipstick correctly before starting the engine. Start and run the engine at idling speed for approx. 30 seconds. Turn off the motor. Wait 30 seconds and check the oil level. If necessary fill so that the oil comes up to the FULL mark on the dipstick.

English – 35

Image 35
Contents English 520D 525DContents After the first 25 hours Pre-delivery serviceTowing IntroductionDear Customer Driving and transport on public roadsGood service Symbols KEY to SymbolsLocation of the controls What is WHAT?General use Safety InstructionsSafety instructions Insure your RiderThis is what you do Driving on slopesChildren MaintenanceTransport Presentation Lowering the Unit Mowing Position Adjusting the cutting heightLever for hydraulic lift of attachments Lifting the Cutting Unit Transport PositionFueling Lights and power outletSafety instructions SeatBypass valves Instrument panelAuxiliary lift system Rops Roll Over Protective StructureStart the engine Starting and driving when coldStarting Engine Before startingRemove the cables in the reverse order Starting the engine with a weak batteryConnecting the jump leads Stop the engine DrivingDriving the Rider BrakingOther objects which can be thrown out by the blades Cutting tipsStarting Completed Maintenance schedule800 Checking the engine’s cooling air intake CleaningRemoving of the machine hoods Change pump and alternator belt Adjustment of pump and alternator beltAdjusting the parking brake Replacement of fuel filterReplacing the air filter Cleaning the air filterCleaning the engine and muffler Cleaning the filter coverChecking the tyre pressure Check the safety systemReplacing the light bulbs Main fuseFitting the cutting head Check the batteryCutting Unit Components Trapping your hand Pins are loosened. Observe caution to avoidRemoving the cutting unit Lift arms move with great force whenPlacing in the service position Service position for the cutting unitCutting height Cutting height and tilt angle adjustmentRestoring from service position Tilt angle Replacing the cutting unit beltsChecking the blades Removing the BioClip plugChange PTO belts Adjustment of PTO beltsGlycol Water Freezing point Change coolantGeneral Lubrication scheduleUniversal drive shaft joints AccessoriesPivot wheel bearings Cutting unit bevel gearJoint bearing Drive shaft front support bearingDrive shaft rear support bearing Steering cylinderDrained directly after stopping the engine Changing the oil filterCheck the hydraulic system oil level Replacing the engine oilLubricating the cables Knobs for setting the cutting heightLubricate the parking brake wire Driver seatEngine does not run smoothly Problem Procedure Engine does not startEngine seems to have no power Starter motor does not turn over the engineUneven mowing Battery does not chargeEngine overheats Electrical System Wiring diagram P 520D Electrical System Electrical System Electrical System Electrical System Electrical System Wiring diagram P525 D Electrical System Electrical System Electrical System Electrical System Electrical System Guard ServiceWinter storage Technical Data Vibration levels see note EC-declaration of conformity Applies to Europe onlySound levels see note Original instructions 1154837-26 ´z+Vsh¶6¨ ´z+Vsh¶6¨