Husqvarna P 525D Introduction, Dear Customer, Driving and transport on public roads, Towing, Use

Page 4

INTRODUCTION

Dear Customer,

Thank you for choosing a Husqvarna Rider. Husqvarna Riders are built to a unique design with a front-mounted cutting unit and a patented articulated steering. Riders are designed for maximum efficiency even in small or confined areas. The closely grouped controls and pedal-operated hydrostatic transmission also contribute to the performance of this machine.

This operator’s manual is a valuable document. By following its instructions (on operation, service, maintenance, etc.) you will significantly extend the life of the machine and even its second-hand value.

When you sell your Rider, make sure you pass on the operator’s manual to the new owner.

The last chapter in the operator’s manual consists of a Service Journal. Make sure that all service work and repairs are recorded. A well-documented service history reduces the costs of seasonal maintenance and influences the second-hand value of the machine. Bring the operator’s manual with the Rider when bringing it to a workshop for service procedures.

Driving and transport on public roads

Check the relevant road traffic regulations before driving the machine on a public road. If transporting the machine on another vehicle always use approved securing devices and make sure that the machine is securely held.

Towing

When your machine is equipped with a hydrostatic transmission you should only tow the machine over short distances and at a low speed, otherwise there is a risk of damaging the transmission.

The transmission must be disengaged when towing, see instructions under the heading Bypass valves.

Use

This ride-on mower is designed to mow grass on open and level ground surfaces. In addition, there is a number of accessories recommended by the manufacturer that broadens the application area. Please contact your dealer for more information about which accessories are available. The machine may only be used with the equipment recommended by the manufacturer. All other types of use are incorrect. Compliance with and strict adherence to the conditions of operation, service and repair as specified by the manufacturer also constitute essential elements of the intended use.

IMPORTANT INFORMATION The transmission guarantee is only valid if the synchronisation of the front and rear wheels has been checked and adjusted in compliance with the service schedule. The system will be damaged if synchronisation is not carried out.

This machine should be operated, serviced and repaired only by persons who are familiar with its particular characteristics and who are acquainted with the relevant safety procedures.

Accident prevention regulations, all other generally recognised regulations on safety and occupational medicine, and all road traffic regulations must be observed at all times.

Any arbitrary modifications carried out to this machine may relieve the manufacturer of liability for any resulting damage or injury.

4 – English

Page 3 Page 5
Image 4
Page 3 Page 5
Contents 520D 525D EnglishContents Pre-delivery service After the first 25 hoursIntroduction Dear CustomerDriving and transport on public roads TowingGood service KEY to Symbols SymbolsWhat is WHAT? Location of the controlsSafety Instructions Safety instructionsInsure your Rider General useDriving on slopes This is what you doMaintenance ChildrenTransport Presentation Adjusting the cutting height Lever for hydraulic lift of attachmentsLifting the Cutting Unit Transport Position Lowering the Unit Mowing PositionLights and power outlet Safety instructionsSeat FuelingInstrument panel Bypass valvesRops Roll Over Protective Structure Auxiliary lift systemStarting and driving when cold Starting EngineBefore starting Start the engineConnecting the jump leads Starting the engine with a weak batteryRemove the cables in the reverse order Driving Driving the RiderBraking Stop the engineCutting tips Other objects which can be thrown out by the blades800 Maintenance scheduleStarting Completed Removing of the machine hoods CleaningChecking the engine’s cooling air intake Adjustment of pump and alternator belt Adjusting the parking brakeReplacement of fuel filter Change pump and alternator beltCleaning the air filter Cleaning the engine and mufflerCleaning the filter cover Replacing the air filterCheck the safety system Replacing the light bulbsMain fuse Checking the tyre pressureCutting Unit Components Check the batteryFitting the cutting head Pins are loosened. Observe caution to avoid Removing the cutting unitLift arms move with great force when Trapping your handService position for the cutting unit Placing in the service positionRestoring from service position Cutting height and tilt angle adjustmentCutting height Replacing the cutting unit belts Checking the bladesRemoving the BioClip plug Tilt angleAdjustment of PTO belts Change PTO beltsChange coolant Glycol Water Freezing pointLubrication schedule GeneralAccessories Pivot wheel bearingsCutting unit bevel gear Universal drive shaft jointsDrive shaft front support bearing Drive shaft rear support bearingSteering cylinder Joint bearingChanging the oil filter Check the hydraulic system oil levelReplacing the engine oil Drained directly after stopping the engineKnobs for setting the cutting height Lubricate the parking brake wireDriver seat Lubricating the cablesProblem Procedure Engine does not start Engine seems to have no powerStarter motor does not turn over the engine Engine does not run smoothlyEngine overheats Battery does not chargeUneven mowing Electrical System Wiring diagram P 520D Electrical System Electrical System Electrical System Electrical System Electrical System Wiring diagram P525 D Electrical System Electrical System Electrical System Electrical System Electrical System Winter storage ServiceGuard Technical Data Sound levels see note EC-declaration of conformity Applies to Europe onlyVibration levels see note 1154837-26 ´z+Vsh¶6¨ ´z+Vsh¶6¨ Original instructions
Top Page Image Contents