Husqvarna 265 ACX manual Boundaries within the working area, Secondary areas

Page 25

3. INSTALLATION

When Automower® searches for the charging station or follows the loop according to the function Follow loop (3-2)(see page 52), it runs along the side of the boundary wire at a specific distance. The Corridor width (3-2-3)function determines the distance from the boundary wire that the mower shall run. It is recommended to state as high a Corridor width value as possible. A high Corridor width value reduces the risk of tracks forming. For more information about Corridor width (3-2-3), see page 54.

In exceptional cases Automower® can be set to straddle the boundary wire, that is to say, half the mower inside the loop and the other half outside. The boundary wire must then be kept at a distance of about 50 cm from all the boundaries of the working area and from the edges of a passage.

Boundaries within the working area

Use the boundary wire to demarcate areas inside the working area by creating islands around obstacles that can not withstand a collision, for example, flower beds and fountains. Run the cable out to the area, route it around the area to be demarcated and then back along the same route. If staples are used, the wire should be laid under the same staple on the return route. When the boundary wire to and from the island are close together, the mower can drive over the wire.

Obstacles that can withstand a collision, for example, trees or bushes higher than 15 cm, do not need to be demarcated by the boundary wire. Automower® will turn when it collides with this type of obstacle.

However, for the most gentle and silent operation, it is preferable to demarcate all fixed objects in and around the working area.

Obstacles that slope slightly, for example, stones or large trees with raised roots, should be demarcated or removed. Automower® can otherwise slide up onto this kind of obstacle causing the blades to be damaged.

Secondary areas

It is recommended to create a secondary area when the working area is made up of two areas that are joined by a passage where the distance between the boundary wires is less than 80 cm. Run the boundary wire then around the secondary area so that it forms an island outside of the main area.

Automower® must be moved manually between the main and secondary areas. Use the MAN operating mode when Automower® shall mow a secondary area.

Instead of creating an island with the existing boundary wire, a secondary area generator can ideally be used. A secondary area generator can be purchased as an accessory. Contact your dealer for further information.

Secondary

area

Main area

English - 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Husqvarna Automower 265 ACX OPERATOR’S Manual Page Table of Contents Table of Contents Introduction Introduction and safetySymbols on Automower Xxxxxx xxxxx xxxx xxxx xxxxx Symbols in the Operator’s ManualImportant Information Xxxxxx xxxxx xxxx xxxx xxxxx Use Safety instructionsTransport MaintenancePresentation Automower, what’s what? Capacity Function of AutomowerMowing technique Working method Movement pattern Search method 3 Follow guide wire Search method 2 Follow boundary wireSearch method Search method 1 IrregularOne Automower in several gardens More than one Automower in a gardenGPS communication unit Carry out the installation in the following steps InstallationPreparations Best charging station location Installation of the charging stationImportant Information Installation Do not tread or walk on the charging station plate Installation and connecting the charging stationAutomower cannot be used before the installation is complete Charging the batteryBest position for the boundary wire Installation of the boundary wireBoundaries for the working area Secondary areas Boundaries within the working areaPassages when searching for the charging station Passages when mowingSlopes Laying out the boundary wire Joining the boundary wire Laying the boundary wire in towards the charging stationConnecting the boundary wire Installation Linking Automower to the charging station Checking the installationNeed of a guide wire Installation of the guide wirePlacement and connection of the guide wire Maximum 135º 90º Activate the GPS anti-theft Protection area Use Charging a discharged batteryUsing GPS-communication Using the timerSMS feature Remarks Commands Description CommandsGPS anti-theft protection Starting Automower Stopping Automower Switching off AutomowerRestart Restart within 20 secondsAdjusting the cutting height Control panel Shortcuts Numbers Main switchMain menu Menu functionsBrowse between menus Number seriesAutomower Main menu Timer CommandsYES Reset all timersStart time 1 Stop time 1 Start time 2 Stop time 2 Mon Tue Wed Thu Fri Sat Sun Run allReversing distance InstallationStart angle 1 End angle 1Gardens where the front and back are joined by a To follow the boundary wire or a guide wire awayPassage where the charging station cannot be When this function is activated Automower willDistance DirectionProportion Follow loopCorridor width Test Test OUT Drive past wire SettingsOpen NormalTime lock4-1-2 PIN codeGPS Alarm4-1-3Set date Set timeTime format Date formatGarden example Proposed installation and settingsExit angles 250 Exit anglesCorridor width Guide 1 Exit angles 70 Battery MaintenanceWinter storage ServiceAutomower Charging stationAfter winter storage CleaningUnderframe and blade disc ChassisTransport and moving Replacing the bladesBody Fault messages Trouble shootingTrouble Shooting Trouble Shooting Fault symptom Data Automower 265 ACX Technical dataData GPS communication unit Environmental Information Environmental informationEU Declaration of Conformity only applies to Europe EU declaration of conformityPage Page Original Instructions
Related manuals
Manual 2 pages 27.84 Kb
Top Page Image Contents