Mitsubishi Electronics CP900E manuals
Computer Equipment > Printer
When we buy new device such as Mitsubishi Electronics CP900E we often through away most of the documentation but the warranty.
Very often issues with Mitsubishi Electronics CP900E begin only after the warranty period ends and you may want to find how to repair it or just do some service work.
Even oftener it is hard to remember what does each function in Printer Mitsubishi Electronics CP900E is responsible for and what options to choose for expected result.
Fortunately you can find all manuals for Printer on our side using links below.
Mitsubishi Electronics CP900E Manual
60 pages 895.78 Kb
1 THIS OPERATION MANUAL IS IMPORTANT TO YOU2 CONTENTS3 SAFETY PRECAUTIONS4 MAINTAIN GOOD VENTILATIONUNSUITABLE LOCATIONS PLACES WITH HIGH HUMIDITY AND DUST PLACES NOT LIKELY TO BE EXTREMELY HOT PLACE THE UNIT ON A HORIZONTAL LEVEL PROTECT AGAINST DEW FORMATION OPERATING AMBIENT TEMPERATURE RANGE UNSUITABLE MATERIALS FOR THE COLOUR VIDEO COPY PROCESSOR CARE OF THE CABINET HEAD ABRASION CONNECTING DEVICES The power cord must be disconnected after printing is over CAUTION ON RELOCATING Periods: According to the recommendations of the manufacturer of the medical devices Scope: a) Visual inspection b) Functionality test accessories c) Electrical test Testing of electrical safety of the system according to EN60601-1 High humidity or dust Also avoid locations subject to corrosive gasses and smoke Heat 5 Consideration relating to the choice shall include:-use of the accessory in the PATIENT VICINITY The transportation and storage environmental conditions are: Temperature Humidity NOTE: As for paper sheet set, refer to Page 17, “Paper sheet set” •When the printed paper is touched by wet hand, the print may be discoloured •Do not use paper other than the specified one Immediately after the paper is replaced •A finger print or dust on the paper surface may degrade the printing quality Note: The use of non-treatedpaper may cause premature head failure in your product 6 SPECIAL FEATURES7 UNPACKING8 FEATURES & FUNCTIONS9 Potential equalization connector1REMOTE TERMINAL 2 (MINI DIN 8 PIN) 2REMOTE TERMINAL 1 (STEREO JACK) 3RS-232CPORT 4VIDEO SIGNAL INPUT/OUTPUT TERMINAL Use these terminals to connect this unit to VIDEO signal equipment. See pages 5IMPEDANCE SWITCH [IMPEDANCE RGB SYNC.] 6S-VIDEOINPUT/OUTPUT TERMINAL Use these terminals to connect to S-VIDEOsignal equipment. See pages 7RGB ANALOG INPUT TERMINALS [R G/G+SYNC B H+V-SYNC] 8RGB ANALOG OUTPUT TERMINALS 9AC LINE SOCKET PRECAUTIONS FEATURES CONNECTIONS PREPARATION PRINTING 10 5SET BUTTON6STOP BUTTONS 7MEMORY PAGE BUTTON Press to print the image memorized by the MEMORY button 9PROGRAM BUTTON 1COLOR ADJUST BUTTON Press to display the COLOR ADJUST menu. See page 2FIELD/FRAME BUTTON See page 3DISPLAY BUTTON 4PRINT QUANTITY {, } BUTTONS A{, }, [, ] BUTTONS BMENU BUTTON Press to display MAIN MENU used for various settings. See pages CCLEAR BUTTONS Press to eliminate all or a part of memorized images DMONITOR BUTTON EMEMORY BUTTON 11 CONNECTIONS12 3 Pressbutton to }select INPUT menu 4 Press button. ] 5 Press or button{ to }select “IN SYNC” 6Set the sync. signal level according to the equipment to be connected. Press or button[to select] “ttl”, “sog” or “0.3v” sog 7Press SET button 8 Press or button{ to }select OUTPUT menu 9 Press APress or button{to select} first “OUT SYNC” . Press button[ to ]select “auto” or “user” auto user When setting “user” on to be connected. Press or button[ to ]select “0.3v” or “ttl.” C Press or button{ to }select third “OUT SYNC” DSet the monitor’s polarity according to the equipment to be connected. Press or button[to select] “nega” or “posi.” 13 E Pressbutton{ to }select “RGB SOG ” F Press button[ to ]select “on” or “off” off GPress SET button IPress SET button The setting of the sync. polarity and signal is completed 14 Impedance switchfor sync.signal 15 RS-232C 2TERMINAL SIGNALPin number Signal line name Description Directions Protective TXD Transmitted data Output RXD Received data Input RTS Request to send CTS Clear to send DSR Data set ready GND Signal ground DTR Data terminal ready (DB25)(DB25) RS-232Connection Cable Computer (DB9) Printer (DB25) GND Press MENU button, then press STOP button on remote control unit button to }select “RS232C.” 16 4 Press button. ]5 Press or button{ to }select “BAUD RATE” 6 Press button[ to ]select “1200”, “2400”, “4800” or “9600” (bit/s) 7 Press button{ to }select “COMMAND TYPE” button[ to ]select “a” , “b” or “c” 9Press SET button APress or button[to memorize] the setting in “prg.1” “prg.2” or “prg.3.” BPress SET button The setting of BAUD RATE and COMMAND TYPE is completed CSet the communication format of the computer with a computer connected 17 BEFORE OPERATION19 PRECAUTIONS2 ON SETTING THERMAL PAPER• Do not use defective paper Do not use the bent or wrinkled paper • Adjust the paper position correctly • Do not slack the roll paper Set the paper tightly to remove any slack • Make the paper side even INCORRECTCORRECT •Other cautions Keep the •Do not touch the rubber roller. Do not stain or damage the roller surface •Do not touch the cutter blade INSTALLING2 THE INK SHEET Colored roller 1Put the ink sheet rollers with flat tops into the holes of ink cassette Put the white roller (rolled with ink sheet) to the ink cassette first Then, put the colored roller (without ink sheet) to the ink cassette 2Put the other sides of rollers. Set IC at this time IC chip with the IC holder is attached to the ink sheet Set the IC holder to the ink cassette as shown right 20 INSTALLING2 THE INK CASSETTE1Eliminate any slack of the ink sheet 2Insert the ink cassette with the ink sheet into its compartment INSERT THE2 PRINTING UNIT 1Push the printing unit until it is locked into place 2After plugging the power cord, press POWER button on the front panel 4Repeat the above step 3 once or twice 21 The installation of print paper and ink cassette is completedBEFORE PRINTING2 AFTER PRINTING2 STORAGE2 22 PRINTING (BASIC)23 6Press SET buttonThe source image is displayed The selecting of input signal is completed 2SELECTING PRINT SIZE •Select “AUTO” or “S” according to the print size AUTO : Selects print size automatically according to the installed ink sheet L : Prints with L size S : Prints with S size •The print size can be set on the menu displayed on the monitor screen and LCD 1Press MENU button and MAIN MENU is displayed 2Press {, } button to select “LAYOUT” 3Press ] button •LAYOUT is displayed Press 24 5Press SET button•MAIN MENU is displayed •This menu lets you select a program memory (1-3)to store your new settings When “CANCEL” is selected, the settings are not memorized The print size setting is completed FRAME 25 2MEMORIZING AND PRINTING AN IMAGE1Display the image which you wish to print 2Press MEMORY button •The selected page is shown in yellow 3Press PRINT button •The image displayed on the monitor will be printed The memory page which is print However, only selecting page can be printed 2IMAGE MEMORIZING WITH PAGE INCREMENT SET TO PAGE •When selecting OFF(PRN SELECT) in MULTI, the memory page is switched in order of A→ B→ C→ D→ A→ B... by pressing MEMORY button 26 MULTI : OFFFRAME FIELD PRINT EXAMPLE 3 pages (PRN 4 pages 8 pages SELECT) 27 2MULTIPLE COPY OR CONTINUOUS PRINTING1Press PRINT Q’ty {,} button to set the number of sheets to be printed •The number of prints is displayed on the monitor screen The number will increase by pressing PRINT Q’ty •The number switches in the order of; 2Press PRINT button •The number of prints you set is printed •If you wish to stop printing; •Press PRINT Q’ty { and } buttons. After printing the current page 28 PRINTING (SPECIAL)prints size L prints size S 29 2WHEN SETTING TO MODE : DIFF, IMAGES :4;1Press DISPLAY button to display the set condition 3Press MEMORY button to store the image to be printed 2WHEN SETTING TO MODE : SAME, IMAGES : 4; 30 prints size L prints size S31 Circuit inside and pin NoJACK) Function Ground Earth Memory : When the signal becomes “LOW” from “HIGH”, the image is stored in memory. (When the signal has been “LOW” for 15ms or more, the image is stored in memory. See page 51, 52.) BUSY1 Refer to the BUSY LEVEL setting of REMOTE SET in SERVICE MENU. See page | IOL | = 2mA or less, | IOH | = 1mA or less Plug pin No 32 2EXTERNAL REMOTE TERMINAL SIGNAL ALLOCATION (MINI DIN8PIN)33 2PIN NO. 6 REMOTE TERMINALremote control unit supplied can be controlled 01: [ button 02: ] button 03: } button 04: { button 08: PRINT Q’ty { button 09 0A*: MENU button 0B*: CLEAR button 0C: PRINT Q’ty } button 0D 0E*: SET button 0F*: STOP button 12*: PROGRAM button 13*: PRINT button 15*: FIELD/FRAME button 16*: COLOR ADJ button 17*: MEMORY button 18*: DISPLAY button 1C*: MEMORY PAGE button 1D*: MONITOR button In case of the codes with * mark, 5 words are sent 2 TIMING CHART Input signal level TTL Input timing >0.4 ms Print code 1.5 ms < T2 < 2 ms 2 ms < T3 < 4.2 ms = 13 = 0 1 0 0 1 13 ms < T4 < 90 ms 34 SETTING THE FUNCTIONS (MENU CHART)35 p46 System setting displayp48 Layout setting p47 Gamma level setting display p45 SERVICE MENU display Analog colour Button function setting display RS-232Csignal setting display Remote signal setting display Previous error display 36 MC:SELECT colorLCD display The menus in the broken lines are indicated by , button{. } MC;SELECT color p38 MAIN MENU display M;INPUT rgb P1R FR A1 Q01 L MENU 2 S 2 2S CG 9 C ML;MODE auto Print setting diplay or CK900L4P(HX)EU MP;GRAD COMMENT Position setting display MM;LINE 37 S;SYSTEMSystem setting display SS;INC SG;COLOR all Layout setting display SL:PRN VAREA SA;INPUT SI;FIELD normal Output signal setting display SO;MONI RSUB0 SK;KEY LOCK S2;BAUD RATE1200 2400 4800 SR;BUSY LEVEL low hi NO ERROR 38 ADJUSTMENTS & SETTINGS (MAIN MENU)39 5Press or button[ to ]select an item or change value“SAVE PRG 1/2/3/CANCEL” is displayed This menu lets you select a program memory (1-3)to store your new settings If you wish to cancel the setting, select CANCEL and press SET button 8Press SET button again •The image will be printed according to the selected memory program 40 B&WAUTO MULTI OFF(PRN SELECT) 41 SAMEDIFF PHOTO1 IMAGES SIZE COPY TOP/BOTTOM/LEFT/RIGHT TOP BOTTOM LEFT RIGHT 42 GRADECHO NOR DIR REV MIRROR PRN SPEED FAST NORMAL 43 Comment modeON[SET] ADJ DATA Comment display 3 Character table 4 Editing mode INS DEL SAVE MAKING A2COMMENT 1Select ON with button and]press SET button 2Select the position where the letter is inputted 3Move the cursor to the character table with , , , {buttons} [. ] Then, select a desired letter 44 5Repeat steps 2 to 4 to complete a commentLINE H-POSI V-POSI H-START FRONT 45 ADJUSTMENTS & SETTINGS (SERVICE MENU)46 INCREMENTPART BUZZER REMAINING Q’ty 0 ~20 REMAIN NOTICE PRN B&P REMAINING SCREEN ERROR SCREEN AUTO FEED&CUT THERMAL 47 PAPER HOLDAUTO CUT INIT PROG ALL MAIN SERVICE INITIALIZE GO[SET] INIT:[CLEAR] EACH 48 Hi/Mid/LowPOINT(Hi/Mid/Low) Selects the point to adjust the colour depth Pointing lighter colour much lighter; Set the setting level for POINT(Hi) and Hi higher PRN V AREA Adjusts the vertical position of memory image Setting area -10~ 10 (adjusts 2 lines each) •This menu is displayed only when IMAGES is set for 2 in L size paper SEPARATE Selects whether a white frame is added to each print or not the settings of LAYOUT) Prints with white frame MARGIN CUT Cuts the margin of the printed paper shows S size Margin is not cut Margin is cut INPUT Selects processing of video signal Processes as colour video signal Processes as monochrome video signal. (The image is shown in black and white.) Adjusts the brightness of the printing image CONT(Contrast) Adjusts the contrast of the printing image Adjusts blue-subcontrastof the printing image. Blue is added with Adjusts density of the printing image. The colour of the image gets deeper with and lighter]with APT(Aperture) Adjusts the contour of image. The contour is reinforced with and softened with , the values]of BRT CONT, R-SUB, G-SUB, B-SUB,COLOR,and APT will be reset to the centre value Initializes each setting in ANALOG COLOR ADJ Gray part is cut when MARGIN CUT is ON 49 FIELDAFC AGC DCF IN SYNC TTL SOG 50 MONI R-SUBMONI B-SUB LIVE SEL ANA DIG CONVERT MEMORY SYNC EXT INT USER NEGA POSI RGB SOG OUT KEY LOCK 51 KEEP MONIAUTO CLEAR OFF MEM MEM&PRN MEM&STOP MEM&MONI AFTER PRN CLEAR KEY 52 This menu does not work when selecting THERMAL : ON or MULTI : OFF(PRN SELECT)BAUD RATE Set the baud rate of RS-232C Set the baud according to the connecting device COMMAND TYPE Sets the command type of RS-232C Selects the command type of RS-232Cto control this unit RESPONSE computer or not Does not send response Sends normal response ERR RES OK Selects the response code when an error occurs Sends the regular response ILL Sends “job end” even if ILLEGAL error occurs INV Sends “job end” even if INVALID error occurs Sends “job end” when any error occurs NO DSR Sets to use 232C, DSR and DTR Sets “NO DSR” according to the connecting device Uses NO DSR Does not use NO DSR BUSY LEVEL on the rear panel LOW “LOW” HIGH “HIGH” •The default setting is “HIGH” BUSY 1,2 SELECT PRINTING Outputs BUSY signal during printing MECHA ERR MEDIA ERR MEMORY STOP REMAINING 53 SYNCHRONOUS2 SETTING FOR MEMORY54 ERROR MESSAGES & COUNTERMEASURES56 The stored image in the memory cannot be enlarged to fill the maxim print areaIs the S size ink sheet installed when selecting “S” in MODE : AUTO/S? Or is the L size ink sheet installed when selecting “AUTO” in MODE : AUTO/S →Check the current setting. Refer to pages Is the paper size set to “N” in the size setting in LAYOUT menu →Check the setting of the print area. Refer to pages The set comments do not appear on the print paper Is the colour of the image stored in the memory adjusted Is INPUT in ANALOG COLOR ADJ set to “COLOR” →Set INPUT to “B&W”. Refer to page Is the image on the monitor screen adjusted Adjust the image on the monitor screen with “MONI Is the COMMENT set to “OFF” →Set COMMENT to “ON”. Refer to page 43. Is the comment inputted →Input the comment on the menu. Refer to pages Wired remote control unit cannot be operated unit → Connect the plug of the remote control unit to the REMOTE terminal on the unit external remote terminal on the rear panel of this unit Is the wired remote control unit for this unit (accessory) used →Use the remote control unit for this unit Is PAPER HOLD set to “ON”, and is printed paper kept at the print outlet →Remove the printed paper from the print outlet. Is KEY LOCK set to “ON” →Set KEY LOCK to “OFF” The printing unit cannot be opened Is the paper cut after prinitng with THERMAL : ON and AUTO CUT : OFF →Press MEMORY button while pressing MONITOR button to cut the printed paper 57 1Press OPEN button to pull out the printing mechanism2Remove the ink cassette with ink sheet 3 Remove the print paper as shown right 4Cut the defective part of the print paper with scissors 5Cut both edges of the print paper 6Install the print paper. (Refer to pages 17-18.) 58 CLEANING59 SPEC & OPTIONS
Also you can find more Mitsubishi Electronics manuals or manuals for other Computer Equipment.