Manuals / Brands / Computer Equipment / Printer / Mitsubishi Electronics / Computer Equipment / Printer

Mitsubishi Electronics CP900E INSERT THE2 PRINTING UNIT, INSTALLING2 THE INK CASSETTE, 1Eliminate any slack of the ink sheet, 4Repeat the above step 3 once or twice

1 60

Download 60 pages, 895.78 Kb

BEFORE OPERATION

NOTE

•Do not remove the IC chip or IC holder from the ink sheet.

Removal of the IC will stop the printer from functioning correctly.

• Set the projected part of the IC holder to the correct position as shown below.

IC holder

Projected part

INSTALLING2 THE INK CASSETTE1Eliminate any slack of the ink sheet.

Hold the colored roller and turn the white roller.

2Insert the ink cassette with the ink sheet into its compartment.

Put the ink cassette of the ink sheet with flat top side to each 1. Then, set the other side (with handle) as shown right. When exchanging the ink cassette and so on, remove it by holding the handle. (See page 57.)

NOTE

Do not install the ink cassette when printing with thermal paper, otherwise printing may be failed.

INSERT THE2 PRINTING UNIT1Push the printing unit until it is locked into place.2After plugging the power cord, press POWER button on the front panel.

3After the set conditions are displayed on the monitor, press MEMORY button about 1 second with holding MONITOR button on the front panel.

The print paper is automatically cut after feeding about 10 cm (4 inches).

4Repeat the above step 3 once or twice.

Fingerprints and dust can be removed by feeding the print paper. The printing unit is initialized.

1 1

22

20

Contents

THIS OPERATION MANUAL IS IMPORTANT TO YOU CONTENTS SAFETY PRECAUTIONS MAINTAIN GOOD VENTILATION UNSUITABLE LOCATIONS PLACES WITH HIGH HUMIDITY AND DUST PLACES NOT LIKELY TO BE EXTREMELY HOT PLACE THE UNIT ON A HORIZONTAL LEVEL Consideration relating to the choice shall include: -use of the accessory in the PATIENT VICINITY The transportation and storage environmental conditions are: Temperature Humidity SPECIAL FEATURES UNPACKING FEATURES & FUNCTIONS Potential equalization connector 1REMOTE TERMINAL 2 (MINI DIN 8 PIN) 2REMOTE TERMINAL 1 (STEREO JACK) 3RS-232CPORT 4VIDEO SIGNAL INPUT/OUTPUT TERMINAL 5SET BUTTON 6STOP BUTTONS 7MEMORY PAGE BUTTON Press to print the image memorized by the MEMORY button 9PROGRAM BUTTON CONNECTIONS 3 Press button to }select INPUT menu 4 Press button. ] 5 Press E Press button{ to }select “RGB SOG ” F Press button[ to ]select “on” or “off” off Impedance switch for sync.signal RS-232C 2TERMINAL SIGNAL Pin number Signal line name Description Directions 4 Press button. ] 5 Press or button{ to }select “BAUD RATE” 6 Press button[ to ]select “1200”, “2400”, “4800” or “9600” (bit/s) BEFORE OPERATION Page PRECAUTIONS2 ON SETTING THERMAL PAPER • Do not use defective paper Do not use the bent or wrinkled paper • Adjust the paper position correctly • Do not slack the roll paper INSTALLING2 THE INK CASSETTE 1Eliminate any slack of the ink sheet 2Insert the ink cassette with the ink sheet into its compartment INSERT THE2 PRINTING UNIT 1Push the printing unit until it is locked into place The installation of print paper and ink cassette is completed BEFORE PRINTING2 AFTER PRINTING2 STORAGE2 PRINTING (BASIC) 6Press SET button The source image is displayed The selecting of input signal is completed 2SELECTING PRINT SIZE •Select “AUTO” or “S” according to the print size 5Press SET button •MAIN MENU is displayed •This menu lets you select a program memory (1-3)to store your new settings When “CANCEL” is selected, the settings are not memorized The print size setting is completed 2MEMORIZING AND PRINTING AN IMAGE 1Display the image which you wish to print 2Press MEMORY button •The selected page is shown in yellow 3Press PRINT button MULTI : OFF FRAME FIELD PRINT EXAMPLE 3 pages 2MULTIPLE COPY OR CONTINUOUS PRINTING 1Press PRINT Q’ty {,} button to set the number of sheets to be printed •The number of prints is displayed on the monitor screen The number will increase by pressing PRINT Q’ty •The number switches in the order of; PRINTING (SPECIAL) prints size L prints size S 2WHEN SETTING TO MODE : DIFF, IMAGES :4; 1Press DISPLAY button to display the set condition 3Press MEMORY button to store the image to be printed 2WHEN SETTING TO MODE : SAME, IMAGES : 4; prints size L prints size S Circuit inside and pin No JACK) Function Ground Earth 2EXTERNAL REMOTE TERMINAL SIGNAL ALLOCATION (MINI DIN8PIN) 2PIN NO. 6 REMOTE TERMINAL remote control unit supplied can be controlled 01: [ button 02: ] button 03: } button SETTING THE FUNCTIONS (MENU CHART) p46 System setting display p48 Layout setting p47 Gamma level setting display p45 SERVICE MENU display Analog colour MC:SELECT color LCD display The menus in the broken lines are indicated by , button{. } MC;SELECT color S;SYSTEM System setting display SS;INC SG;COLOR all ADJUSTMENTS & SETTINGS (MAIN MENU) 5Press or button[ to ]select an item or change value “SAVE PRG 1/2/3/CANCEL” is displayed This menu lets you select a program memory (1-3)to store your new settings If you wish to cancel the setting, select CANCEL and press SET button 8Press SET button again B&W AUTO MULTI OFF(PRN SELECT) SAME DIFF PHOTO1 IMAGES SIZE GRAD ECHO NOR DIR REV Comment mode ON[SET] ADJ DATA Comment display 5Repeat steps 2 to 4 to complete a comment LINE H-POSI V-POSI H-START ADJUSTMENTS & SETTINGS (SERVICE MENU) INCREMENT PART BUZZER REMAINING Q’ty 0 ~20 PAPER HOLD AUTO CUT INIT PROG ALL MAIN Hi/Mid/Low POINT(Hi/Mid/Low) Selects the point to adjust the colour depth Pointing lighter colour much lighter; Set the setting level for POINT(Hi) and Hi higher FIELD AFC AGC DCF IN SYNC MONI R-SUB MONI B-SUB LIVE SEL ANA DIG KEEP MONI AUTO CLEAR OFF MEM MEM&PRN MEM&STOP MEM&MONI This menu does not work when selecting THERMAL : ON or MULTI : OFF(PRN SELECT) BAUD RATE Set the baud rate of RS-232C Set the baud according to the connecting device COMMAND TYPE Sets the command type of RS-232C Selects the command type of RS-232Cto control this unit SYNCHRONOUS2 SETTING FOR MEMORY ERROR MESSAGES & COUNTERMEASURES Page The stored image in the memory cannot be enlarged to fill the maxim print area Is the S size ink sheet installed when selecting “S” in MODE : AUTO/S? Or is the L size ink sheet installed when selecting “AUTO” in MODE : AUTO/S →Check the current setting. Refer to pages Is the paper size set to “N” in the size setting in LAYOUT menu 1Press OPEN button to pull out the printing mechanism 2Remove the ink cassette with ink sheet 3 Remove the print paper as shown right 4Cut the defective part of the print paper with scissors 5Cut both edges of the print paper CLEANING SPEC & OPTIONS