Power LED Green | 3Com 3CRWDR200A-75, 3CRWDR200B-75, WL-553 manual

Front Panel 15

■The Router has just been started up and is running a self-test routine, or

■The administrator has invoked the Reset to Factory Defaults command, or

■The system software is in the process of being upgraded

In each of these cases, wait until the Router has completed the current operation and the alert LED is Off.

Flashing slowly — The Router has completed the Reset to Factory Defaults process, and is waiting for you to reset the unit. To do this, remove power, wait 10 seconds and then re-apply power. The Router will then enter the start-up sequence and resume normal operation.

On for 2 seconds, and then off — The Router has detected and prevented a hacker from attacking your network from the Internet.

Continuously on — A fault has been detected with your Router during the start-up process. Refer to Chapter 6 “Troubleshooting”.

2Power LED Green

Indicates that the Router is powered on.

3Wireless LAN (WLAN) Status LED Yellow

If the LED is on it indicates that wireless networking is enabled. If the LED is flashing, data is being transmitted or received. If the LED is off, the Wireless LAN has been disabled in the Router, or there is a problem. Refer to Chapter 6 “Troubleshooting”.

4Four LAN Status LEDs

Green (100 Mbps link) / yellow (10 Mbps link)

If the LED is on, the link between the port and the next piece of network equipment is OK. If the LED is flashing, the link is OK and data is being transmitted or received. If the LED is off, nothing is connected, the connected device is switched off, or there is a problem with the connection (refer to Chapter 6 “Troubleshooting”). The port will automatically adjust to the correct speed and duplex.

5Sync DSL Status LED

Image 15

3Com 3CRWDR200A-75, 3CRWDR200B-75, WL-553 manual Power LED Green

Contents

OfficeConnect 3Com Corporation Campus Drive Marlborough, MA USA Contents Running the Setup Wizard WAN Using Discovery END User Software License Agreement Page Conventions About this Guide Text Conventions Configure your Router Introducing the Router Example Network Without a Firewall Router Advantages Firewall Router Minimum System Component Requirements Front PanelOperations Power LED Green Socket Rear Panel Power Adapter OK LED Introducing the Router Safety Information IntroductionPositioning the Router Stacking the Router Using the RubberWall Mounting Feet IP Address Subnet Mask Default Router address DNS address Page Connecting the Router Hardware Installation Automatically Details on how to obtain an IP address automaticallyObtaining an IP Address Local Area Properties Screen Restart your computer Obtaining an IP Address Automatically Macintosh Disabling PPPoEPptp Client Software Disabling Web ProxyUse Proxy Server option is unchecked Setting UP Your Computers Wizard Accessing Country Selection Screen Welcome Welcome Screen Wizard Screen Password Change Administration Password Screen Click Next to display the Time Zone setup screen WAN Settings Internet Settings Screen PPPoE Screen PPPoE Mode PPPoA Screen PPPoA Mode Dynamic/Fixed IP in Bridge Mode Dynamic/Fixed IP in 1483 Bridge Mode IP over ATM Screen IP over ATM ModeIPoA Bridging Mode Screen Bridging Mode Dhcp Server Setup Screen Accessing the Wizard Summary Configuration Summary Screen Pages ConfigurationNavigating Through the Router Getting Help Changing the Administration Password Unit Configuration LAN SettingsFor information on how to run the wizard LAN Settings menu provides the following options LAN Settings Static Dhcp Dhcp Lease Table Dhcp Lease Table Screen Please select your country from the drop-down list Enable Wireless NetworkingWireless Mode Country Domain Enable Broadcast Ssid Service Area Name/SSID Profile Support for NICs WEP To enable WEP, select WEP from the Encryption Type WPA with Radius Click Save to save the settingTo enable WPA, select WPA-PSKor WPA2-PSKfrom the Encryption Type Enter the Radius Port number Enter the Radius Server IP address Edca AP Paramenters Txop Transmission Opportunity WMM Wireless Multimedia Edca STA Parameters Connection Control Screen Client List Screen Client List Advanced Wireless Settings Screen Wireless Settings Router Configuration WDS Screen PPPoA PPP over ATM Firewall PPPoEIPoA IP over ATM Virtual Servers Screen Virtual Server Special Applications Special Applications Screen Click Apply to save the configuration and apply the changes Single DMZMultiple DMZ SPI Screen PC Privileges PC Privileges Screen Router Configuration Schedule Rules Screen Content Filter Screen Make sure the Enable Content Filter check box is checked URL Filter Screen To enable the URL Filtering, please do the following System Tools Items Restart, Time Zone, Configuration, and Upgrade Restart Restart Screen Time Zone Time Zone Screen Backup Configuration Restore Configuration DataReset to Factory Default Upgrade Upgrade Screen Advanced Service, ProxyARP, Port Mapping, and IPSec RIP screen Setting Up RIP Ddns screen TZO.com NOIP.com Quality of Service QoS Screen Proxy ARP Screen IPSec Screen Port Mapping Screen Management Check Enable System Log box Snmp Screen UPnP Screen Check UPnP Enabled to activate UPnP Remote Management Screen Disable Remote Administration This option is set as default Diagnostics Device Info Diagnostics Screen Summary The Summary Screen Statistics The Statistics Screen ARP screen is used to display the ARP status Support Support Screen Feedback Feedback Screen Router Configuration Browsing to the Router Configuration Screens Basic ConnectionChecks Factory Defaults Connecting toForgotten Password Reset to Networking Wireless Troubleshooting Power LED or Power Adapter OKLED Not Lit Further advice Recovering fromFault with the hardware. Remove power from the Router, wait Seconds and then re-apply power. If the Alert LED comes on How do I reset the Router to Factory Defaults? Frequently Asked Questions Http//knowledgebase.3com.com 3Com Warranty and Support Services 3Com Warranty and Support Services Troubleshooting Application Windows Installation 95/98/2000/Me/NT/ XPRunning Discovery Discovered Router Screen TCP working together. TCP/IP is an internationally adopted Protocol SuiteManaging the Router over the Network Internet protocol suite consists of a well-defined set Type Two Type One How does a Device Obtain an IP Address and Subnet Mask? Appendix B IP Addressing Adsl Wireless 11g 108Mbps Firewall Router InterfacesWlan Interfaces Weight Operating TemperaturePower Dimensions Maximum cable length of 100m 327.86 ft System Requirements Operating Systems Appendix C Technical Specifications Important Safety Information Safety Information Wichtige Sicherheitshinweise Consignes importantes de sécurité Appendix D Safety Information Agreement Appendix E END User Software License Agreement Glossary Chapter Glossary Ethernet Address See MAC address IP Address RouterHalf Duplex Hub Protocol MAC AddressNetwork Card NIC Chapter Glossary Traffic The movement of data packets on a network Area Index Index Regulatory Including interference that may cause undesired operation Ycanada IC Même si ce brouillage est susceptible de compromettre le That the Industry Canada technical specifications were metPower Eirp is not more than that required for successful Installed outdoors is subject to licensing 141 142 Page USA