Important Safety Instructions | Acer M11E specs

IMPORTANT SAFETY

INSTRUCTIONS

1.Read these instructions carefully. Save these instructions for future reference.

2.Follow all warnings and instructions marked on the product.

3.Do not use this product near water.

4.Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.

5.Slots and openings in the cabinet and the back or bottom are provided for ventilation; to ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation is provided.

6.This product should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.

7.This product is equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug.

8.Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord.

iii

Image 3

Acer M11E manual Important Safety Instructions

Contents

M11E System Copyright Important Safety Instructions Page Page CD ROM Safety Warning Vii FCC Class B Radio Frequency Interference Statement Manual Structure About this Manual Purpose Conventions Table of Contents Xii Bios Utility Xiii Xiv List of Figures List of Tables Page System Board Features User’s Guide Major Components System Board Layout System Board Layout with Network Connector System Board Layout without Network Connector Jumper and Connector Locations Jumpers and Connectors Blackened pin of a jumper or connector represents pin Connector Functions Jumper Settings JP1 ESD Precautions Attaching the Processor Fan Sink Installing the Pentium II processor Removing tape protector from Fan SInk Locking a Wide Clip End 10 Locking the metal bracket 11 Installing the Pentium II Retention Mechanism Installing a Pentium II Processor 12 Installing the Pentium II Retention Mechanism 13 Installing a Pentium II Processor 14 Securing the Pentium II Processor Removing a Pentium II Processor 16 Removing the Pentium II Processor Memory Configurations Memory Upgrade 17 Installing a Dimm Installing a Dimm 18 Removing a Dimm Removing a Dimm Reconfiguring the System Installing PCI Cards Installing Expansion Cards Bios detects and configures only PnP cards Installing ISA Cards 20 Installing an ISA Card Installing an AGP Card 21 Installing an AGP Card Error Messages Software Error MessagesSystem Error Messages System Board Mmmmssssooo Wxxxx Correcting Error Conditions Page Setup Utility Setup Utility Entering Setup Setup Utility System Information Processor Processor SpeedInternal Cache Size IDE Primary Channel Master External CacheFloppy Drive a Floppy Drive B Parallel Port IDE Secondary Channel SlaveTotal Memory Serial Port 15 PS/2 Mouse Main Board ID Product InformationProduct Name System S/N System Bios Version DMI Bios VersionMain Board S/N Floppy Drives Disk Drives 2 LS-120 Drive Compatible As IDE DrivesIDE Primary Channel Master IDE Primary Channel Slave IDE Secondary Channel MasterIDE Secondary Channel Slave This parameter specifies the size of your hard disk, in MB Enhanced IDE Features Disabled DMA Transfer Mode Onboard Peripherals Serial Ports 1Base Address ∙ 3BCh ∙ 378h ∙ 278h Operation Mode Onboard Device Settings USB Host Controller Floppy Disk ControllerIDE Controller PS/2 Mouse Controller Onboard Ethernet Chip SMBus Interrupt IRQ9 Power Management Power Management ModeIDE Hard Disk Standby Timer System Wake-up Event Power Switch 4 secSystem Sleep Timer Modem Ring Indicator Boot Sequence Boot Options Fast Boot Silent BootFirst Hard Disk Drive Memory Test Num Lock After BootConfiguration Table Boot from LANDesk Service Agent Date Date and Time Time Memory/Cache Options Advanced Options Internal Cache CPU Cache External CacheMemory at 15MB-16MB Reserved for Memory Parity Mode 2 PnP/PCI OptionsFor system board with LAN For system board without LAN PCI IRQ Setting VGA Palette Snoop PCI IRQ Sharing Plug and Play OS Reset Resource AssignmentsCPU Frequency Graphics Aperture Size Bus Frequency CPU MultipleProcessor Speed Setup Password To set or change a PasswordSystem Security Setup Utility To remove your Setup Password To bypass Setup Password Make sure to set JP3 to 1-2 to enable Power-on password Power-on Password Disk Drive Control Drive Control Settings Abort Settings Change Load Default Settings Exit Setup