System Information | Acer M11E specification

2.2System Information

The following screen appears if you select System Information from the Main menu:

System Information

Processor	Pentium II
Processor Speed	300 MHz
Internal Cache Size	32 KB, Enabled
External Cache Size	512 KB, Enabled
Floppy Drive A	1.44	MB, 3.5-inch
Floppy Drive B	None
IDE Primary Channel Master	Hard Disk, xxx MB
IDE Primary Channel Slave	None
IDE Secondary Channel Master	None
IDE Secondary Channel Slave	None
Total Memory	xxx MB
1st Bank	SDRAM, xxx MB
2nd Bank	None
3rd Bank	None

The System Information menu shows the current basic configuration of your system.

The next screen shows page 2 of the System Information menu.

2-4	User’s Guide

Image 52

Acer M11E manual System Information

Contents

M11E System Copyright Important Safety Instructions Page Page CD ROM Safety Warning Vii FCC Class B Radio Frequency Interference Statement About this Manual Purpose Manual Structure Conventions Table of Contents Bios Utility Xii Xiii List of Figures Xiv List of Tables Page Features System Board User’s Guide Major Components System Board Layout with Network Connector System Board Layout System Board Layout without Network Connector Jumpers and Connectors Jumper and Connector Locations Blackened pin of a jumper or connector represents pin Jumper Settings Connector Functions JP1 ESD Precautions Installing the Pentium II processor Attaching the Processor Fan Sink Removing tape protector from Fan SInk Locking a Wide Clip End 10 Locking the metal bracket Installing a Pentium II Processor 11 Installing the Pentium II Retention Mechanism 12 Installing the Pentium II Retention Mechanism 13 Installing a Pentium II Processor Removing a Pentium II Processor 14 Securing the Pentium II Processor 16 Removing the Pentium II Processor Memory Upgrade Memory Configurations Installing a Dimm 17 Installing a Dimm Removing a Dimm 18 Removing a Dimm Reconfiguring the System Installing Expansion Cards Installing PCI Cards Installing ISA Cards Bios detects and configures only PnP cards Installing an AGP Card 20 Installing an ISA Card 21 Installing an AGP Card Software Error Messages Error MessagesSystem Error Messages System Board Mmmmssssooo Wxxxx Correcting Error Conditions Page Setup Utility Entering Setup Setup Utility Setup Utility System Information Processor Speed ProcessorInternal Cache Size External Cache Floppy Drive aFloppy Drive B IDE Primary Channel Master IDE Secondary Channel Slave Total MemorySerial Port Parallel Port 15 PS/2 Mouse Product Information Product NameSystem S/N Main Board ID DMI Bios Version System Bios VersionMain Board S/N Disk Drives Floppy Drives IDE Drives 2 LS-120 Drive Compatible AsIDE Primary Channel Master IDE Secondary Channel Master IDE Primary Channel SlaveIDE Secondary Channel Slave This parameter specifies the size of your hard disk, in MB Disabled Enhanced IDE Features DMA Transfer Mode Serial Ports 1 Onboard PeripheralsBase Address ∙ 3BCh ∙ 378h ∙ 278h Onboard Device Settings Operation Mode Floppy Disk Controller IDE ControllerPS/2 Mouse Controller USB Host Controller SMBus Interrupt IRQ9 Onboard Ethernet Chip Power Management Mode Power ManagementIDE Hard Disk Standby Timer Power Switch 4 sec System Sleep TimerModem Ring Indicator System Wake-up Event Boot Options Boot Sequence Silent Boot Fast BootFirst Hard Disk Drive Num Lock After Boot Configuration TableBoot from LANDesk Service Agent Memory Test Date and Time Date Time Advanced Options Memory/Cache Options External Cache Internal Cache CPU CacheMemory at 15MB-16MB Reserved for 2 PnP/PCI Options Memory Parity ModeFor system board with LAN PCI IRQ Setting For system board without LAN PCI IRQ Sharing VGA Palette Snoop Reset Resource Assignments CPU FrequencyGraphics Aperture Size Plug and Play OS CPU Multiple Bus FrequencyProcessor Speed To set or change a Password Setup PasswordSystem Security Setup Utility To remove your Setup Password To bypass Setup Password Power-on Password Make sure to set JP3 to 1-2 to enable Power-on password Drive Control Settings Disk Drive Control Load Default Settings Abort Settings Change Exit Setup