Boot Options, Boot Sequence | Acer M11E specification

2.7Boot Options

This option allows you to specify your preferred setting for bootup.

The following screen appears if you select Boot Options from the Basic Configuration menu:

Boot Options

Boot Sequence

1st [Floppy Disk]

2nd [Hard Disk ]

3rd [IDE CD-ROM ]

First Hard Disk Drive	[ IDE]
Fast Boot	[Auto]
Silent Boot	[Enabled]
Num Lock After Boot	[Enabled]
Memory Test	[Enabled]
*Configuration Table	[Enabled]
Boot from LanDesk Service Agent ....	[Disabled]

The above parameter marked with ‘*’ will only appear if you access the advanced configuration level in the Main Menu. Please refer to section 2.1 for more information.

2.7.1Boot Sequence

This parameter allows you to specify the boot search sequence during POST.

∙1st. The system checks this drive first.

2-24	User’s Guide

Image 72

Acer M11E manual Boot Options, Boot Sequence

Contents

M11E System Copyright Important Safety Instructions Page Page CD ROM Safety Warning Vii FCC Class B Radio Frequency Interference Statement About this Manual Purpose Manual Structure Conventions Table of Contents Bios Utility Xii Xiii List of Figures Xiv List of Tables Page Features System Board User’s Guide Major Components System Board Layout with Network Connector System Board Layout System Board Layout without Network Connector Jumpers and Connectors Jumper and Connector Locations Blackened pin of a jumper or connector represents pin Jumper Settings Connector Functions JP1 ESD Precautions Installing the Pentium II processor Attaching the Processor Fan Sink Removing tape protector from Fan SInk Locking a Wide Clip End 10 Locking the metal bracket Installing a Pentium II Processor 11 Installing the Pentium II Retention Mechanism 12 Installing the Pentium II Retention Mechanism 13 Installing a Pentium II Processor Removing a Pentium II Processor 14 Securing the Pentium II Processor 16 Removing the Pentium II Processor Memory Upgrade Memory Configurations Installing a Dimm 17 Installing a Dimm Removing a Dimm 18 Removing a Dimm Reconfiguring the System Installing Expansion Cards Installing PCI Cards Installing ISA Cards Bios detects and configures only PnP cards Installing an AGP Card 20 Installing an ISA Card 21 Installing an AGP Card Error Messages Software Error MessagesSystem Error Messages System Board Mmmmssssooo Wxxxx Correcting Error Conditions Page Setup Utility Entering Setup Setup Utility Setup Utility System Information Processor Processor SpeedInternal Cache Size External Cache Floppy Drive aFloppy Drive B IDE Primary Channel Master IDE Secondary Channel Slave Total MemorySerial Port Parallel Port 15 PS/2 Mouse Product Information Product NameSystem S/N Main Board ID System Bios Version DMI Bios VersionMain Board S/N Disk Drives Floppy Drives 2 LS-120 Drive Compatible As IDE DrivesIDE Primary Channel Master IDE Primary Channel Slave IDE Secondary Channel MasterIDE Secondary Channel Slave This parameter specifies the size of your hard disk, in MB Disabled Enhanced IDE Features DMA Transfer Mode Onboard Peripherals Serial Ports 1Base Address ∙ 3BCh ∙ 378h ∙ 278h Onboard Device Settings Operation Mode Floppy Disk Controller IDE ControllerPS/2 Mouse Controller USB Host Controller SMBus Interrupt IRQ9 Onboard Ethernet Chip Power Management Power Management ModeIDE Hard Disk Standby Timer Power Switch 4 sec System Sleep TimerModem Ring Indicator System Wake-up Event Boot Options Boot Sequence Fast Boot Silent BootFirst Hard Disk Drive Num Lock After Boot Configuration TableBoot from LANDesk Service Agent Memory Test Date and Time Date Time Advanced Options Memory/Cache Options Internal Cache CPU Cache External CacheMemory at 15MB-16MB Reserved for Memory Parity Mode 2 PnP/PCI OptionsFor system board with LAN PCI IRQ Setting For system board without LAN PCI IRQ Sharing VGA Palette Snoop Reset Resource Assignments CPU FrequencyGraphics Aperture Size Plug and Play OS Bus Frequency CPU MultipleProcessor Speed Setup Password To set or change a PasswordSystem Security Setup Utility To remove your Setup Password To bypass Setup Password Power-on Password Make sure to set JP3 to 1-2 to enable Power-on password Drive Control Settings Disk Drive Control Load Default Settings Abort Settings Change Exit Setup