External Cache, Floppy Drive a, Floppy Drive B | Acer M11E guide

2.2.4External Cache

This parameter specifies the second-level cache memory size currently supported by the system. The available cache sizes are 256 KB or 512 KB (depending on the CPU installed). For information on how to configure the system memory, see section 2.9.1

2.2.5Floppy Drive A

This parameter specifies the system’s current diskette drive A settings. For information on how to configure the floppy drives, see section 2.4.1.

2.2.6Floppy Drive B

This parameter specifies the system’s current diskette drive B settings. For information on how to configure the floppy drives, see section 2.4.1.

2.2.7IDE Primary Channel Master

This parameter specifies the current configuration of the IDE device connected to the master port of the primary IDE channel. For information on how to configure the IDE drives, see section 2.4.3.

2.2.8IDE Primary Channel Slave

This parameter specifies the current configuration of the IDE device connected to the slave port of the primary IDE channel. For information on how to configure the IDE drives, see section 2.4.3.

2.2.9IDE Secondary Channel Master

This parameter specifies the current configuration of the IDE device connected to the master port of the secondary IDE channel. For information on how to configure the IDE drives, see section 2.4.3.

2-6	User’s Guide

Image 54

Acer M11E manual External Cache, Floppy Drive a, Floppy Drive B, IDE Primary Channel Master, IDE Primary Channel Slave

Contents

M11E System Copyright Important Safety Instructions Page Page CD ROM Safety Warning Vii FCC Class B Radio Frequency Interference Statement About this Manual Purpose Manual Structure Conventions Table of Contents Bios Utility Xii Xiii List of Figures Xiv List of Tables Page Features System Board User’s Guide Major Components System Board Layout with Network Connector System Board Layout System Board Layout without Network Connector Jumpers and Connectors Jumper and Connector Locations Blackened pin of a jumper or connector represents pin Jumper Settings Connector Functions JP1 ESD Precautions Installing the Pentium II processor Attaching the Processor Fan Sink Removing tape protector from Fan SInk Locking a Wide Clip End 10 Locking the metal bracket Installing a Pentium II Processor 11 Installing the Pentium II Retention Mechanism 12 Installing the Pentium II Retention Mechanism 13 Installing a Pentium II Processor Removing a Pentium II Processor 14 Securing the Pentium II Processor 16 Removing the Pentium II Processor Memory Upgrade Memory Configurations Installing a Dimm 17 Installing a Dimm Removing a Dimm 18 Removing a Dimm Reconfiguring the System Installing Expansion Cards Installing PCI Cards Installing ISA Cards Bios detects and configures only PnP cards Installing an AGP Card 20 Installing an ISA Card 21 Installing an AGP Card Error Messages Software Error MessagesSystem Error Messages System Board Mmmmssssooo Wxxxx Correcting Error Conditions Page Setup Utility Entering Setup Setup Utility Setup Utility System Information Processor Processor SpeedInternal Cache Size Floppy Drive B External CacheFloppy Drive a IDE Primary Channel Master Serial Port IDE Secondary Channel SlaveTotal Memory Parallel Port 15 PS/2 Mouse System S/N Product InformationProduct Name Main Board ID System Bios Version DMI Bios VersionMain Board S/N Disk Drives Floppy Drives 2 LS-120 Drive Compatible As IDE DrivesIDE Primary Channel Master IDE Primary Channel Slave IDE Secondary Channel MasterIDE Secondary Channel Slave This parameter specifies the size of your hard disk, in MB Disabled Enhanced IDE Features DMA Transfer Mode Onboard Peripherals Serial Ports 1Base Address ∙ 3BCh ∙ 378h ∙ 278h Onboard Device Settings Operation Mode PS/2 Mouse Controller Floppy Disk ControllerIDE Controller USB Host Controller SMBus Interrupt IRQ9 Onboard Ethernet Chip Power Management Power Management ModeIDE Hard Disk Standby Timer Modem Ring Indicator Power Switch 4 secSystem Sleep Timer System Wake-up Event Boot Options Boot Sequence Fast Boot Silent BootFirst Hard Disk Drive Boot from LANDesk Service Agent Num Lock After BootConfiguration Table Memory Test Date and Time Date Time Advanced Options Memory/Cache Options Internal Cache CPU Cache External CacheMemory at 15MB-16MB Reserved for Memory Parity Mode 2 PnP/PCI OptionsFor system board with LAN PCI IRQ Setting For system board without LAN PCI IRQ Sharing VGA Palette Snoop Graphics Aperture Size Reset Resource AssignmentsCPU Frequency Plug and Play OS Bus Frequency CPU MultipleProcessor Speed Setup Password To set or change a PasswordSystem Security Setup Utility To remove your Setup Password To bypass Setup Password Power-on Password Make sure to set JP3 to 1-2 to enable Power-on password Drive Control Settings Disk Drive Control Load Default Settings Abort Settings Change Exit Setup