Floppy Disk Controller, IDE Controller | Acer M11E specs

or Disabled

Onboard Device Settings

Floppy Disk Controller	[Enabled	]
IDE Controller	[Both	]
PS/2 Mouse Controller	[Enabled ]
USB Host Controller	[Disabled]
USB Legacy Mode	[--------]
SMBus Interrupt(IRQ9)	[Disabled]
Onboard Ethernet Chip	[Enabled ]

Floppy Disk Controller

This parameter lets you enable or disable the onboard floppy disk controller.

IDE Controller

Set this parameter to Primary to enable only the primary IDE controller; Both to enable both primary and secondary IDE controllers;

to disable all IDE controllers.

PS/2 Mouse Controller

This parameter enables or disables the onboard PS/2 mouse controller.

USB Host Controller

This parameter lets you enable or disable the USB controller on board. When enabled, it activates the USB function of the system. When disabled, it deactivates the function.

2-20	User’s Guide

Image 68

Acer M11E manual Floppy Disk Controller, IDE Controller, PS/2 Mouse Controller, USB Host Controller

Contents

M11E System Copyright Important Safety Instructions Page Page CD ROM Safety Warning Vii FCC Class B Radio Frequency Interference Statement About this Manual Purpose Manual Structure Conventions Table of Contents Bios Utility Xii Xiii List of Figures Xiv List of Tables Page Features System Board User’s Guide Major Components System Board Layout with Network Connector System Board Layout System Board Layout without Network Connector Jumpers and Connectors Jumper and Connector Locations Blackened pin of a jumper or connector represents pin Jumper Settings Connector Functions JP1 ESD Precautions Installing the Pentium II processor Attaching the Processor Fan Sink Removing tape protector from Fan SInk Locking a Wide Clip End 10 Locking the metal bracket Installing a Pentium II Processor 11 Installing the Pentium II Retention Mechanism 12 Installing the Pentium II Retention Mechanism 13 Installing a Pentium II Processor Removing a Pentium II Processor 14 Securing the Pentium II Processor 16 Removing the Pentium II Processor Memory Upgrade Memory Configurations Installing a Dimm 17 Installing a Dimm Removing a Dimm 18 Removing a Dimm Reconfiguring the System Installing Expansion Cards Installing PCI Cards Installing ISA Cards Bios detects and configures only PnP cards Installing an AGP Card 20 Installing an ISA Card 21 Installing an AGP Card System Error Messages Error MessagesSoftware Error Messages System Board Mmmmssssooo Wxxxx Correcting Error Conditions Page Setup Utility Entering Setup Setup Utility Setup Utility System Information Internal Cache Size ProcessorProcessor Speed External Cache Floppy Drive aFloppy Drive B IDE Primary Channel Master IDE Secondary Channel Slave Total MemorySerial Port Parallel Port 15 PS/2 Mouse Product Information Product NameSystem S/N Main Board ID Main Board S/N System Bios VersionDMI Bios Version Disk Drives Floppy Drives IDE Primary Channel Master 2 LS-120 Drive Compatible AsIDE Drives IDE Secondary Channel Slave IDE Primary Channel SlaveIDE Secondary Channel Master This parameter specifies the size of your hard disk, in MB Disabled Enhanced IDE Features DMA Transfer Mode Base Address Onboard PeripheralsSerial Ports 1 ∙ 3BCh ∙ 378h ∙ 278h Onboard Device Settings Operation Mode Floppy Disk Controller IDE ControllerPS/2 Mouse Controller USB Host Controller SMBus Interrupt IRQ9 Onboard Ethernet Chip IDE Hard Disk Standby Timer Power ManagementPower Management Mode Power Switch 4 sec System Sleep TimerModem Ring Indicator System Wake-up Event Boot Options Boot Sequence First Hard Disk Drive Fast BootSilent Boot Num Lock After Boot Configuration TableBoot from LANDesk Service Agent Memory Test Date and Time Date Time Advanced Options Memory/Cache Options Memory at 15MB-16MB Reserved for Internal Cache CPU CacheExternal Cache For system board with LAN Memory Parity Mode2 PnP/PCI Options PCI IRQ Setting For system board without LAN PCI IRQ Sharing VGA Palette Snoop Reset Resource Assignments CPU FrequencyGraphics Aperture Size Plug and Play OS Processor Speed Bus FrequencyCPU Multiple System Security Setup PasswordTo set or change a Password Setup Utility To remove your Setup Password To bypass Setup Password Power-on Password Make sure to set JP3 to 1-2 to enable Power-on password Drive Control Settings Disk Drive Control Load Default Settings Abort Settings Change Exit Setup