FCC Class B Radio Frequency Interference Statement | Acer M11E

FCC Class B Radio Frequency

Interference Statement

Note:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1.Reorient or relocate the receiving antenna.

2.Increase the separation between the equipment and receiver.

3.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4.Consult the dealer or an experienced radio/television technician for help.

Notice 1:

The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Notice 2:

Shielded interface cables, if any, must be used in order to comply with the emission limits.

viii

Image 8

Acer M11E manual FCC Class B Radio Frequency Interference Statement

Contents

M11E System Copyright Important Safety Instructions Page Page CD ROM Safety Warning Vii FCC Class B Radio Frequency Interference Statement About this Manual Purpose Manual Structure Conventions Table of Contents Bios Utility Xii Xiii List of Figures Xiv List of Tables Page Features System Board User’s Guide Major Components System Board Layout with Network Connector System Board Layout System Board Layout without Network Connector Jumpers and Connectors Jumper and Connector Locations Blackened pin of a jumper or connector represents pin Jumper Settings Connector Functions JP1 ESD Precautions Installing the Pentium II processor Attaching the Processor Fan Sink Removing tape protector from Fan SInk Locking a Wide Clip End 10 Locking the metal bracket Installing a Pentium II Processor 11 Installing the Pentium II Retention Mechanism 12 Installing the Pentium II Retention Mechanism 13 Installing a Pentium II Processor Removing a Pentium II Processor 14 Securing the Pentium II Processor 16 Removing the Pentium II Processor Memory Upgrade Memory Configurations Installing a Dimm 17 Installing a Dimm Removing a Dimm 18 Removing a Dimm Reconfiguring the System Installing Expansion Cards Installing PCI Cards Installing ISA Cards Bios detects and configures only PnP cards Installing an AGP Card 20 Installing an ISA Card 21 Installing an AGP Card System Error Messages Error MessagesSoftware Error Messages System Board Mmmmssssooo Wxxxx Correcting Error Conditions Page Setup Utility Entering Setup Setup Utility Setup Utility System Information Internal Cache Size ProcessorProcessor Speed External Cache Floppy Drive aFloppy Drive B IDE Primary Channel Master IDE Secondary Channel Slave Total MemorySerial Port Parallel Port 15 PS/2 Mouse Product Information Product NameSystem S/N Main Board ID Main Board S/N System Bios VersionDMI Bios Version Disk Drives Floppy Drives IDE Primary Channel Master 2 LS-120 Drive Compatible AsIDE Drives IDE Secondary Channel Slave IDE Primary Channel SlaveIDE Secondary Channel Master This parameter specifies the size of your hard disk, in MB Disabled Enhanced IDE Features DMA Transfer Mode Base Address Onboard PeripheralsSerial Ports 1 ∙ 3BCh ∙ 378h ∙ 278h Onboard Device Settings Operation Mode Floppy Disk Controller IDE ControllerPS/2 Mouse Controller USB Host Controller SMBus Interrupt IRQ9 Onboard Ethernet Chip IDE Hard Disk Standby Timer Power ManagementPower Management Mode Power Switch 4 sec System Sleep TimerModem Ring Indicator System Wake-up Event Boot Options Boot Sequence First Hard Disk Drive Fast BootSilent Boot Num Lock After Boot Configuration TableBoot from LANDesk Service Agent Memory Test Date and Time Date Time Advanced Options Memory/Cache Options Memory at 15MB-16MB Reserved for Internal Cache CPU CacheExternal Cache For system board with LAN Memory Parity Mode2 PnP/PCI Options PCI IRQ Setting For system board without LAN PCI IRQ Sharing VGA Palette Snoop Reset Resource Assignments CPU FrequencyGraphics Aperture Size Plug and Play OS Processor Speed Bus FrequencyCPU Multiple System Security Setup PasswordTo set or change a Password Setup Utility To remove your Setup Password To bypass Setup Password Power-on Password Make sure to set JP3 to 1-2 to enable Power-on password Drive Control Settings Disk Drive Control Load Default Settings Abort Settings Change Exit Setup