34

Configuring the ICX-250

External DIP Switches

T1 Interface - CSU/DSX Interface Selection (Dip switch - back)

ICX-250 - Rear Panel

Switch numbers S1 through S5 are shown on the board within the unit.

 

 

 

 

 

 

 

 

 

 

 

 

 

Data 1

 

 

 

 

 

 

 

 

T1

 

 

 

FXS Loop Pairs

FXS Loopback

 

 

 

 

 

 

 

 

T1 Line

Rx

24/48 VDC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

12 13

24

Alm.

Data 1

Data 2

Data 2

 

T1

 

 

Tx

 

+ – G

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

120 VAC–.6A 60Hz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11269-A

 

 

 

 

S5

S4

S3

 

S2

 

S1

 

 

 

 

T1

ONDIP

1 2 3 4 5 6 7

ACCEPT

T1

ONDIP

1 2 3 4 5 6 7

IGNORE

Description: S1 position 5 is used to select whether the T1 acts as a CSU or DSX interface.

Factory Setting: CSUDSX: SlimLine will exhibit DSX interface characteristics.CSU: SlimLine will exhibit CSU interface characteristics.

T1 Interface - CSU/DSX Line Build Out (CSU) or Line Length (DSX) (DIP switch - back)

ICX-250 - Rear Panel

Switch numbers S1 through S5 are shown on the board within the unit.

 

 

 

 

 

 

 

 

 

 

 

 

Data 1

 

 

 

 

 

 

 

 

T1

 

 

 

FXS Loop Pairs

FXS Loopback

 

 

 

 

 

 

 

 

 

 

T1 Line

Rx

24/48 VDC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

12 13

24

Alm.

Data 1

Data 2

Data 2

 

T1

 

 

Tx

 

+ – G

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

120 VAC–.6A 60Hz

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

S5 S4S3S2 S111270-A

 

 

 

 

 

 

T1

 

 

 

 

 

 

 

 

 

 

 

 

 

T1

 

 

 

 

 

 

 

 

 

 

 

 

 

T1

 

 

 

 

 

 

 

ON

 

 

 

 

 

 

 

 

 

DIP

 

ON

 

 

 

 

 

 

 

 

 

DIP

 

ON

 

 

 

 

 

 

 

 

 

DIP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

2

 

3

 

4

 

5

 

6

 

7

 

 

 

1

 

2

 

3

 

4

 

5

 

6

 

 

 

1

 

2

 

3

 

4

 

5

 

6

 

7

 

 

 

 

 

 

0 dB

 

 

 

 

 

 

 

 

 

–7.5 dB

 

 

 

 

 

 

 

 

–15.0 dB

 

 

 

 

Description: S1 position 6 and 7 are used to select CSU/DSX line build out or line length.

Factory Setting: CSU 0dB

Line Build Out: Selects one of three line build out and line length options for either CSU or DSX interfaces.

Selections: CSU 0 dB, –7.5 dB and –15.0 dB; DSX 0.6 dB at 250 ft, 1.8 dB at 500 ft, 3.0 dB at 700 ft.

ADCP-62-023

Issue 1, September 1998

© 1998, ADC Telecommunications, Inc.