External DIP Switches | Configuring the | 35 |
Data Port 1 and 2 - Number of Timeslots (DIP switch - back)
Switch numbers S1 through S5 are shown on the board within the unit.
|
|
|
|
|
|
|
|
|
|
|
| Data 1 |
|
|
|
|
|
|
|
| T1 |
|
| |||
| FXS Loop Pairs | FXS Loopback |
|
|
|
|
|
|
|
|
|
| T1 Line | Rx | 24/48 VDC |
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
|
| 1 | 12 13 | 24 | Alm. | Data 1 | Data 2 | Data 2 |
| T1 |
|
| Tx |
| + – G |
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 120 | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
S5 S4S3S2 S111271-A
Data 1 / Data 2
1 | ON |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| DIP | ||||
0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| 1 |
| 2 |
| 3 |
| 4 |
| 5 |
| 6 |
| 7 |
| 8 |
| 9 |
| 10 |
| 11 |
| 12 |
|
Description: S2 positions 1, 2, 3, 4 and 5 (Data 2 - DIP switch) sets the port parameters for Data Port 2. S3 positions 1, 2, 3, 4 and 5 (Data 1
Factory Setting: All switches are set to zero (data ports inactive).
Number of Timeslots: Selects the number of consecutive timeslots that data from Data Port 1 and/ or 2 will be mapped onto. Please refer to Decimal/Binary Conversion Table (see page 36) for Data Port Configuration to aid in selecting N. Drawing above indicates switch settings if timeslot N = 13. Selected quantity of timeslots x 64K = Data Port Bandwidth.
Note: Binary numbers are used to select the number of timeslots and starting timeslots.
Issue 1, September 1998 |
© 1998, ADC Telecommunications, Inc.