Manuals / ADIC / Computer Equipment / Network Card

ADIC 4000, 7000DLT installation and operation guide Specification

Models: 7000DLT 4000

1 88

Download 88 pages 56.05 Kb

Troubleshooting Specifications Install Symbol Right Indicator Panel LED Connecting the Interface Cable Maintenance Drive Configuration Control or Connector Purpose Setting the Scsi ID

Page 68

A-2 Specification62-0162-01

Page 67 Page 69

Image 68

ADIC 4000, 7000DLT installation and operation guide Specification

Page 67 Page 69

Related pages All Specification page Specifications for Eclipse - Fujitsu Ten AVN5495 Specifications 251 for Toshiba GD-1220 Specifications for Insignia NS-PWLC593-C Amplifier Specifications for Fusion MS-DA51600 Specifications for Sony CDP-CA9ES Appendix a Technical Specifications 110 for Allied Telesis x600-24Ts-POE Specifications for Uniden DSS7915 Baud Rate Specification for GE GEH6505A Specifications for Eizo FlexScan S2110W Where can I find replacement parts for the DeWalt bench grinder eye shield and brackets?

Contents

Installation and Operation Guide Copyright 1999 all rights reserved Contents Operation and Maintenance SafetyInstallation Troubleshooting and Diagnostic Specification Index Drive ConfigurationRegulatory Notices Figures Viii Figures Tables Tables Introduction Introduction 62-0162-01 Organization OverviewIntended Audience Explanation of Symbols and Notes Associated Documents Description Description 62-0162-01 Model DLTTape DLTTape Iiixt Model Drive Model Front Panel Controls and IndicatorsModel Sustained Maximum Description 24000DLT Front Panel Write Protected Rear Panel Controls and Connectors Control or Connector Purpose Color Length ModelCartridge Model Tape Other Requirements Scsi Host Adapter Scsi Interface Cable Application SoftwareAdditional Items Cartridge Requirements Description 62-0162-01 Safety Safety 62-0162-01 Signal Word Definition Consequence Safety ConventionsSymbol Precautions Precautions Safety 62-0162-01 Installation Installation 62-0162-01 Unpacking and Inspecting Installing the Host AdapterConnecting the Interface Cable Connecting More than One 4000/ 7000DLT Series Aisy C hained Setting the Scsi ID Check the Scsi Bus Termination Connecting Power and Turning On Installing the Backup Software Installation 62-0162-01 Operation Maintenance Operation and Maintenance 62-0162-01 Power-on Self-Test Drive State LED Indicator Displays and Drive Actions Drive Status LCD Messages Drive State Label Color State Operating Condition Right Indicator Panel LEDDrive Operating Conditions Left Indicator Panel LED LCD Message Drive Operation LCD Messages 4Drive Operation LCD Messages 4Drive Operation LCD Messages Loading the Data Cartridge Lift up on the Cartridge Insert/Release Handle Data Protection Tape in Use State Meaning Right Indicator PanelRemoving the Data Cartridge Cleaning the Tape Head Push the Cartridge Insert/Release Handle closed Cleaning Tape LED It means You should Cleaning Cycle LCD Messages Cleaning the Enclosure Troubleshooting Diagnostic Troubleshooting and Diagnostic 62-0162-01 Troubleshooting Chart Then You should Problem Chart Use Cleaning Tape LED Why the Use Cleaning Tape LED Gets Turned on High Humidity Troubleshooting and Diagnostic 62-0162-01 Specification Specification General Specification Table A-1 Table A-1 Drive Configuration Drive Configuration DLT4000 Drives Drive Dependent ConfigurationScsi Bus Parity Figure B-3DLT7000 Tape Drive Connectors Right Side DLT7000 Drive Scsi Bus Termination and Terminator Power Figure B-5DLT4000 Tape Drive Connectors right side Then You Should Figure B-7DLT7000 Tape Drive Connectors right side DLT7000 Drives Drive Configuration Regulatory Regulatory Notices FCC Notices U.S. Only Shielded Cables Product Type IC Notice Canada Only EN 55022 Compliance Czech Republic Only CE Notice Vcci Notices Japan Only Index GB format Motion Messages Index in-9 In-10 Index 62-0162-01

Top Page Image Contents