Drive Configuration | ADIC 7000DLT, 4000 instruction

B

Drive

Configuration

Drive Dependent Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-3

SCSI Bus Parity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-3

DLT4000 Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-3

DLT7000 Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-4

SCSI Bus Termination and Terminator Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-5

DLT4000 Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-5

DLT7000 Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-7

Image 71

ADIC 7000DLT, 4000 installation and operation guide Drive Configuration

Contents

Installation and Operation Guide Copyright 1999 all rights reserved Contents Operation and Maintenance SafetyInstallation Specification Troubleshooting and Diagnostic Index Drive ConfigurationRegulatory Notices Figures Viii Figures Tables Tables Introduction Introduction 62-0162-01 Organization OverviewIntended Audience Associated Documents Explanation of Symbols and Notes Description Description 62-0162-01 Model DLTTape DLTTape Iiixt Model Drive Model Front Panel Controls and IndicatorsModel Sustained Maximum Description 24000DLT Front Panel Write Protected Control or Connector Purpose Rear Panel Controls and Connectors Color Length ModelCartridge Model Tape Scsi Host Adapter Other Requirements Cartridge Requirements Scsi Interface CableApplication Software Additional Items Description 62-0162-01 Safety Safety 62-0162-01 Signal Word Definition Consequence Safety ConventionsSymbol Precautions Precautions Safety 62-0162-01 Installation Installation 62-0162-01 Unpacking and Inspecting Installing the Host AdapterConnecting the Interface Cable Aisy C hained Connecting More than One 4000/ 7000DLT Series Setting the Scsi ID Check the Scsi Bus Termination Installing the Backup Software Connecting Power and Turning On Installation 62-0162-01 Operation Maintenance Operation and Maintenance 62-0162-01 Power-on Self-Test Drive Status Drive State LED Indicator Displays and Drive Actions Drive State LCD Messages Label Color State Operating Condition Right Indicator Panel LEDDrive Operating Conditions Left Indicator Panel LED LCD Message Drive Operation LCD Messages 4Drive Operation LCD Messages 4Drive Operation LCD Messages Lift up on the Cartridge Insert/Release Handle Loading the Data Cartridge Tape in Use Data Protection State Meaning Right Indicator PanelRemoving the Data Cartridge Push the Cartridge Insert/Release Handle closed Cleaning the Tape Head It means You should Cleaning Tape LED Cleaning Cycle LCD Messages Cleaning the Enclosure Troubleshooting Diagnostic Troubleshooting and Diagnostic 62-0162-01 Then You should Troubleshooting Chart Problem Chart Use Cleaning Tape LED Why the Use Cleaning Tape LED Gets Turned on High Humidity Troubleshooting and Diagnostic 62-0162-01 Specification Specification Table A-1 General Specification Table A-1 Drive Configuration Drive Configuration DLT4000 Drives Drive Dependent ConfigurationScsi Bus Parity DLT7000 Drive Figure B-3DLT7000 Tape Drive Connectors Right Side Figure B-5DLT4000 Tape Drive Connectors right side Scsi Bus Termination and Terminator Power Then You Should DLT7000 Drives Figure B-7DLT7000 Tape Drive Connectors right side Drive Configuration Regulatory Regulatory Notices Shielded Cables FCC Notices U.S. Only IC Notice Canada Only Product Type CE Notice EN 55022 Compliance Czech Republic Only Vcci Notices Japan Only GB format Index Motion Messages Index in-9 In-10 Index 62-0162-01