Table of Contents | ADTRAN 2 x E1 manual

61280004L2-1C

Table of Contents

	Page
Section 1. Tracer Description
Introduction	1
Applications	1
Spread Spectrum	1
Direct Sequence	2
Coding	2
Channel Selection	2
Forward Error Correction	2
E1 Interfaces	3
Tracer System Configuration	3
Baseband Processor or BBP	3
VT100 RS-232 Interface	4
Alarm Contacts	5
IF Signal	5
Power	5
Controls and Indicators	5
Non-volatile Memory	7
Built-In Tests	8
Radio Frequency Converter or RFC	8
Antenna Selection	10
Section 2. Installation
Unpack, Inspect	11
Rackmounted RFC Configuration	11
Mastmounted RFC Configuration	11
Installation	11
Location and Mounting	11
Power Requirements	11
Grounding	12

TRACER 2 x E1 User’s Manual

iii

Image 5

ADTRAN 2 x E1 user manual Table of Contents

Contents

Tracer 2 x E1 User’s Manual 61280004L2-1C R N I N G Radio Frequency Interface Statement Radio Frequency Interference Statement Table of Contents Operation Troubleshooting Warranty, Ordering and Return Information SpecificationsGlossary Appendix a Illustrations Viii Introduction Tracer DescriptionApplications Spread Spectrum Tracer Description Forward Error CorrectionChannel Selection Direct Sequence Baseband Processor or BBP Tracer System ConfigurationE1 Interfaces VT100 RS-232 Interface Block diagram of the BBP is shown in Figure If Signal Alarm ContactsPower Controls and Indicators Freq Non-volatile Memory Name Function Radio Frequency Converter or RFC Built-In Tests 10. Front and Rear of Rackmount RFC Housing Antenna 100 mW Antenna Selection UNPACK, Inspect Installation Grounding Installation E1 Interfaces 15 Pin RJ-48 P O R T a N T Link Planning Antenna Gain Antenna Feedline Loss Path Availability Path Loss GHZ, 1 Watt Transmitter Option Setting the Transmitter Power 4 GHz Diplexer Setting the RFC Frequency Plan on NON 1 Watt 2.4 GHZ Models Plan a Plan B 8 GHz Diplexer Setting the RFC Frequency Plan on 5.8 GHZ Models Applying Power Connecting the BBP and the RFCAutomatic BBP Frequency Plan Spreading Code RF LOW CO-LOCATING Multiple SystemsAntenna Alignment Remote Bert Alarm Contacts Installation Operation PasswordVT100 User Interface RS-232 Interface System Status Screen OperationMain Menu Selections Tracer Main Menu Main Menu Screen E1A Status Screen E1 Status / Configuration / Loopback Link Performance History Screen Link Performance History E1B Statistics E1A Statistics Problem Descriptions and Recommended Actions SectionTROUBLESHOOTING4 TroubleshootingTroubleshooting Using the Front Panel Indicators General Recommended Actions TroubleshootingCV/CRC Light on E1A or E1B is Lit when CRC is enabled LOS/OOF Light on E1A or E1B LBK-A or LBK-B is Lit ALM is Lit No Power Light TST Light is Lit After Pressing Remote Test Button Test Light is Lit or Blinking RF Low Light is On Fail Light is Lit After Pressing Remote Test Button CV Alarm Troubleshooting Using the VT100 User InterfaceLOS Alarm RMT Alarm OOF AlarmCRC Alarm UA1 Alarm Code Sync Status Carrier Sync Status or E1 Mux Sync Status ES Values in E1A or E1B Performance History Menu Possible CauseRFC Link Up Status SES Values in E1A or E1B Performance History Menu Troubleshooting Specifications Power SpecificationsVT100 Terminal Interface Mechanical & Environmental Warranty WARRANTY, Ordering and ReturnSales Repairs and Returns Warranty, Ordering and Return Information Acronyms Used in this Manual Glossary Glossary Terminal Connection DB-25 Appendix a Cable ConnectionsPersonal Computer Connection DB-9 Modem Connection DB-25 Appendix a Cable Connections