Manuals / Agilent Technologies / Home Audio / Stereo System

Agilent Technologies 89441A manual Index

Models: 89441A

1 92

Download 92 pages 54.15 Kb

Page 80

Index

filters (continued)
user defined		OP 17-18
video OP 14-3
firmware version, displaying						HT
FM demodulation
algorithm	OP 15-12
example	OP 1-6, OP 3-4
FM demodulation, using					HT
fonts HT
formatting a disk			GS 6-6
fourier transform			OP 13-7
French softkey		HT
freq counter softkey				HT
frequency	HT
about frequency parameters HT
center frequency				HT
frequency counter				HT
frequency span			HT
manual frequency, setting						HT
reference	GS 7-7
signal tracking			HT
span, extending to 8 mhz						HT
start frequency			HT
step size	HT
stop frequency			HT
stop frequency is 10 MHz						GS 7-23
using markers to set step size HT
frequency domain overview						OP 13-2
frequency error (in symbol table)							HT
frequency points			OP 14-5, HT
about frequency points					HT
and display		OP 14-12
memory allocation				HT
setting the number of					HT
frequency resolution				OP 14-11
frequency response measurements							HT

frequency response, measuring GS 5-1 frequency span

and display OP 14-5

and information bandwidth OP 14-3 and resolution bandwidth OP 14-14, OP 14-19

video demodulation OP 17-11, OP 18-12

front panel tour HT

FSK

about FSK HT

block diagram OP 17-5, HT carrier magnitude-error HT

FSK (continued)

carrier offset (in symbol table) HT

deviation (in symbol table)		HT
FSK error (in symbol table)		HT
FSK error trace, displaying		HT
FSK measured	HT
FSK reference	HT

magnitude error (in symbol table) HT setting the span to symbol rate ratio HT state definitions HT

See also demodulation, digital FTP (File Transfer Protocol) HT FTP, and LAN OP 10-10

full span softkey HT fuse GS 7-12

G

gate length softkey HT

gate time-record				HT
displaying			HT
gate delay			HT
gate time HT
gate-delay step size					HT
setting the length of					HT
turning on/off				HT
GATHERING DATA, definition of						HT
gating
description			OP 16-2
example		OP 3-3, OP 4-2, GS 3-1
in analog demodulation OP 15-13
gaussian filters OP 17-18
German softkey				HT
ghosted softkeys				HT
grids HT
1 grid	HT
2 grids		HT
4 grids		HT
hiding	HT
multiple		GS 5-7
overlapped			GS 5-7
grounding requirements GS 7-3
group delay softkey HT
GSM (Group Service Mobile) HT
guardbands, analog demodulation
OP 15-7
GPIB HT
about the GPIB				HT
addressable only HT
devices, setting up					GS 6-2
GPIB address: analyzer HT
GPIB address: external devices						HT

GS = Getting Started Guide	HT = Online Help
OP = Operator's Guide	(press (Help) key)

Image 80

Agilent Technologies 89441A manual Index

Contents

Agilent Technologies 89441A Getting Started Guide The Analyzer at a Glance Front Panel This page left intentionally blank Saftey Summary BEFORE APPLYING POWERGENERAL ENVIRONMENTAL CONDITIONSDO NOT REMOVE THE INSTRUMENT COVER FUSESDO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE Safety Symbols Warning, risk of electric shockCaution, refer to accompanying documents Alternating currentNotation Conventions In This Book To Learn More About the AnalyzerThis page left intentionally blank 1 Using Online Help 3 Using Gating to Characterize a Burst Signal4 Measuring Relative Phase 2 Making Simple Noise MeasurementsInspection and Installation 6 General Tasks7 Preparing the Analyzer for Use Index Documentation Road Map Need AssistanceUsing Online Help To learn about online help To display help for hardkeys and softkeys To display a related help topic Using Online Help1Enter the online help system Press Help 2Display help for a hardkeyTo select a topic from the help index Page Making Simple Noise Measurements To measure random noise To measure band power To measure signal to noise ratios Measured noise band Carrier-to-noiseratio normalized to one HertzPage Using Gating to Characterize a Burst Signal To Use Time Gating 7Examine the second burst Using Gating to Characterize a Burst Signal5Configure the display and the measurement Page Measuring Relative Phase To measure the relative phase of an AM signal 6Activate two traces To measure the relative phase of an PM signal Characterizing a Filter To set up a frequency response measurement 5Start an averaged measurement To use the absolute marker To use the relative marker To use the search marker To display phase To display coherence General Tasks To set up peripherals 2Select the output format and device type To save data with an internal or RAM disk To recall data with an internal or RAM disk To format a disk General Tasks To create a math functionYou can create up to 6 functions and 5 constants To use a math function General TasksPress Measurement Data, math func, F1 4Press Auto ScaleTo display a summary of instrument parameters Page Preparing the Analyzer for Use Preparing the Analyzer for Use AC Line Voltageto chassis ground UL listed for use in the United States of America Preparing the Analyzer for Usenumber for a complete cable including the plug To do the incoming inspection power if it is damaged7Set the IF section’s power switch to on To connect the sections Preparing the Analyzer for Use To install the analyzer measure the line voltage To change the IF section’s line-voltageswitchSelect To change the RF section’s line-voltageswitch AC Line VoltageTo change the IF section’s fuse AC Line VoltageFuse RangeTo change the RF section’s fuse AC Line VoltageFuse RF SectionTo connect the analyzer to a LAN internet protocol address ReturnTo connect the analyzer to a serial device To connect the analyzer to a parallel deviceCommand Reference To connect the analyzer to an GPIB deviceTo connect the analyzer to an external monitor To connect the optional keyboard To connect the optional minimum loss pad To clean the screen lTo store the analyzerlTo transport the analyzer If the IF section will not power up If the RF section will not power up If the analyzer’s stop frequency is 10 MHz Page Index IndexIndex Index See also FSK Indexcontinued Index See also tracesIndex Index Index Index See LANIndex Index See knobblock diagram IndexIndex See also NADCIndex time data OP 14-15time data softkey HTSee also display See also gridsIndex See lanPage Agilent 89400-SeriesDocumentation Roadmap And you want toIf you are thinking about Then read the analyzer’sNeed Assistance?