Manuals / Agilent Technologies / Home Audio / Stereo System

Agilent Technologies 89441A manual To connect the analyzer to a serial device

Models: 89441A

1 92

Download 92 pages 54.15 Kb

Page 65

To connect the analyzer to a serial device

Preparing the Analyzer for Use

To connect the analyzer to a serial device

The IF section’s Serial 1 port is a 9-pin, EIA-574 port that can interface with a

lprinter or plotter. The total allowable transmission path length is 15 meters.

Connect the IF section’s SERIAL 1 port to a printer or plotter using a 9-pin female to 25-pin RS-232-C cable.

Part Number	Cable Description
Agilent 24542G	9-pin female EIA-574 to 25-pin male RS-232
HP 24542H	9-pin female EIA-574 to 25-pin female RS-232

To connect the analyzer to a parallel device

The IF section’s Parallel Port is a 25-pin, Centronics port. The Parallel Port can

linterface with PCL printers or HP-GL plotters.

Connect the IF section’s rear panel PARALLEL PORT connector to a plotter or printer using a Centronics interface cable.

7-15

Image 65

Agilent Technologies 89441A manual To connect the analyzer to a serial device, To connect the analyzer to a parallel device

Contents

Agilent Technologies 89441A Getting Started Guide The Analyzer at a Glance Front Panel This page left intentionally blank BEFORE APPLYING POWER Saftey SummaryGENERAL ENVIRONMENTAL CONDITIONSDO NOT REMOVE THE INSTRUMENT COVER FUSESDO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE Warning, risk of electric shock Safety SymbolsCaution, refer to accompanying documents Alternating currentNotation Conventions To Learn More About the Analyzer In This BookThis page left intentionally blank 3 Using Gating to Characterize a Burst Signal 1 Using Online Help4 Measuring Relative Phase 2 Making Simple Noise Measurements6 General Tasks Inspection and Installation7 Preparing the Analyzer for Use Index Documentation Road Map Need AssistanceUsing Online Help To learn about online help To display help for hardkeys and softkeys Using Online Help To display a related help topic1Enter the online help system Press Help 2Display help for a hardkeyTo select a topic from the help index Page Making Simple Noise Measurements To measure random noise To measure band power To measure signal to noise ratios Carrier-to-noiseratio normalized to one Hertz Measured noise bandPage Using Gating to Characterize a Burst Signal To Use Time Gating 7Examine the second burst Using Gating to Characterize a Burst Signal5Configure the display and the measurement Page Measuring Relative Phase To measure the relative phase of an AM signal 6Activate two traces To measure the relative phase of an PM signal Characterizing a Filter To set up a frequency response measurement 5Start an averaged measurement To use the absolute marker To use the relative marker To use the search marker To display phase To display coherence General Tasks To set up peripherals 2Select the output format and device type To save data with an internal or RAM disk To recall data with an internal or RAM disk To format a disk General Tasks To create a math functionYou can create up to 6 functions and 5 constants General Tasks To use a math functionPress Measurement Data, math func, F1 4Press Auto ScaleTo display a summary of instrument parameters Page Preparing the Analyzer for Use AC Line Voltage Preparing the Analyzer for Useto chassis ground UL listed for use in the United States of America Preparing the Analyzer for Usenumber for a complete cable including the plug power if it is damaged To do the incoming inspection7Set the IF section’s power switch to on To connect the sections Preparing the Analyzer for Use To install the analyzer measure the line voltage To change the IF section’s line-voltageswitchSelect AC Line Voltage To change the RF section’s line-voltageswitchAC Line Voltage To change the IF section’s fuseFuse RangeAC Line Voltage To change the RF section’s fuseFuse RF Sectioninternet protocol address Return To connect the analyzer to a LANTo connect the analyzer to a parallel device To connect the analyzer to a serial deviceCommand Reference To connect the analyzer to an GPIB deviceTo connect the analyzer to an external monitor To connect the optional keyboard To connect the optional minimum loss pad lTo store the analyzer To clean the screenlTo transport the analyzer If the IF section will not power up If the RF section will not power up If the analyzer’s stop frequency is 10 MHz Page Index IndexIndex Index See also FSK Indexcontinued See also traces IndexIndex Index Index See LAN IndexIndex See knob IndexIndex block diagramSee also NADC Indextime data OP 14-15time data softkey HT IndexSee also display See also gridsSee lan IndexPage And you want to Agilent 89400-SeriesDocumentation RoadmapIf you are thinking about Then read the analyzer’sNeed Assistance?