Manuals / Agilent Technologies / Power Tools / Stud Sensor

Agilent Technologies manual E9300/1B and H Power Sensor Specifications

Models: E9300

1 71

Download 71 pages 61.87 Kb

Troubleshooting Specs Spread Spectrum Signal Warranty Connector Type Reassembly Procedure Auto-averaging Settings Cleaning Safety Power Meter Requirements

Page 58

E9300/1B and H Power Sensor Specifications

58

Page 57 Page 59

Image 58

Agilent Technologies manual E9300/1B and H Power Sensor Specifications

Page 57 Page 59

Related pages All Specification page Section Specification Information for Jackson Chemical Sanitizing Glasswasher Dishmachine Series Preliminary Specification Sheet for Curtis FRW080 Specifications for SMC Networks SMC8624T Specifications Duplex Unit AD-14 for Breadman CF2002 VHD Controller Specifications for Vidikron Vision 140 Appendix a Default Settings and Technical Specifications for NETGEAR VPN Firewall 200 FVX538 Specifications for Samsung SCX-5835NX Specifications for Samsung UN32B6000VFXZA Game Mode Specifications for Sharp EL-6053S Specifications for Zephyr CTP-E54SX Where can I find the manual for the Rotel RSX-1067?

Contents

Operating and Service Guide Copyright 1999 Agilent Technologies Legal Information WarrantyCertification Limitation of Warranty Exclusive Remedies General Safety Information Sound Emission Power Meter Front Panel Operation SafetyConventions Sensors Covered by Manual DocumentationRelated Publications Documentation Table of Contents Standing Wave Ratio SWR and Reflection Coefficient Rho Per Introduction Typical HP E-series E9300 power sensors Power Meter Requirements General Information Agilent E-Series E9300 Power Sensors in Detail Simplified Block Diagram of Diode Pair/Attenuator/Diode Pair General Information Getting Started Checking Power Meter Firmware and DSP RevisionInitial Inspection Interconnections and Calibration Specifications Making Measurements What You’ll Find This Chapter Power Meter Configuration Changes Auto-averaging Settings Measuring Spread Spectrum and Multitone Signals Spread Spectrum Signal Cdma Signal Measurements Cdma IS-95A 9Ch Fwd Multitone Signal Measurements 90 % Frequency GHz Typical Lower Range Calibration Factor Power Meter and Sensor Operation Measuring Tdma SignalsAchieving Stable Results with Tdma Signals Achieving Stable Results with GSM Signals Input Settings , More Electromagnetic Compatibility EMC Measurements Setting the Range Measurement Accuracy and Speed Measurement Considerations Accuracy Speed and Averaging Summary Specifications and Characteristics Sensor Low Power Path High Power Path Introduction Connector Type E9300/1/4/A Power Sensor SpecificationsMaximum SWR 0C to +55C Maximum Power Maximum DC Voltage Power Linearity ± 2.5% Typical Power Linearity at 25C, after zero Additional Power Switching Point Zero Set Zero Drift Measurement Noise Settling Time Time E4418B E4419B X2 Mode Calibration Factor and Reflection Coefficient Cal Factor Uncertainty General E9300/1B and H Power Sensor Specifications Frequency Range E9300B Typical SWR 25C ± 10C E9300H Typical SWR 10 MHz to 18 GHz 25C ± 10C Maximum Power Sensor To 35 C To 55 C GHz E9300/1B To 0 dBm To 10 dBm 10 to 20 dBm 20 to 26 dBm For larger changes refer to the following table E9300/1H DBm to 0 dBm +44 +30 dBm E9300/1B Conditions Zero Set Zero Drift2 Measurement Settling Time Typical Cal Factor Uncertainty Low Power Path Cal Factor Uncertainty High Power Path References Storage and Shipment Environment E9300/1B and H Power Sensor Specifications Service Cleaning Connector Cleaning Performance Test Frequency System Rho Actual Maximum Uncertainty Measurement Performance Test Replaceable Parts Is the illustrated parts breakdown IPB that identifies all Illustrated Parts Break down Reference Agilent Part Qty Description Designation Number LABEL, ID E9301B Service Principles of Operation Disassembly Procedure TroubleshootingRepair of Defective Sensor Reassembly Procedure Removing Power Sensor Shell Sales and Service Offices Asia Pacific Europe

Top Page Image Contents