Allied Telesis AT-WA1104G-10 manual PIM6

Models: AT-WA1104G-10

1 99
Download 99 pages 28.11 Kb
Page 14
Image 14

 

 

 

 

 

 

 

 

Features in 291-08

 

 

 

14

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR

Module

Level

Description

AR400

AR7x5

AR7x0S

Rapier i

 

Rapier w

AT8800-

AT-8600

 

AT-8700XL

x90048-

AT-9900

AT-9800

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00014827

PIM6

2

If an IPv6 accelerator was used, and the upstream router forwarded IPv6

-

-

-

-

 

-

-

-

 

-

Y

Y

-

 

 

 

multicast data just before the prune limit timer expired, then the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

downstream router sometimes did not send the prune until significantly

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

after the timer expired.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This issue has been resolved.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00015169

MSTP, GUI

2

Using the web-based GUI to set the Point-to-Point Link in the MSTP CIST

-

-

-

Y

 

Y

Y

Y

 

Y

Y

Y

-

 

 

 

Port configuration to a non-default value would generate an error.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This issue has been resolved.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00015805

ISAKMP, IPv6

2

During the boot up, the router or switch waited 5 seconds before

Y

Y

Y

Y

 

Y

Y

-

 

-

-

-

-

 

 

 

beginning ISAKMP prenegotiation. For VPN tunnels over IPsec for IPv6, this

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

was not long enough for the router or switch’s interfaces to come up before

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

prenegotiation began.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Also, the router or switch did not obtain the most recent active ISAKMP SA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

when multiple SAs existed.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

These issues have been resolved. The router or switch now waits 6 seconds,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

and obtains the most recent SA and uses that for Phase 2 negotiations.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00015964

Switching

2

If the switch had a large number of routes in its forwarding database (FDB),

-

-

-

-

 

-

-

-

 

-

Y

Y

-

 

 

 

and the command show switch fdb was used to display the contents of

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the FDB, and the switch’s CPU was busy at the time, then the switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

sometimes rebooted.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This issue has been resolved.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00016262

Load

2

When attempting to upload files from the switch using TFTP to an IPv4

Y

Y

Y

Y

 

Y

Y

-

 

-

Y

Y

Y

 

 

 

server address, the router or switch reported an error if IPv6 was not

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

enabled. It was not possible to upload files using TFTP to an IPv6 server

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

address at all.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

These issues have been resolved.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00016340

DHCP

2

DHCP Snooping has been enhanced to operate in a customised VLAN ID

-

-

-

Y

 

Y

Y

Y

 

Y

Y

Y

-

 

Snooping

 

translation (VID translation) environment. Previously, DHCP Snooping was

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

not supported with VID translation.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This issue has been resolved.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Version 291-10

C613-10488-00 REV G

Page 14
Image 14
Allied Telesis AT-WA1104G-10 manual PIM6