Allied Telesis AT-WA1104G-10 manual CR00016940, CR00016941, CR00017006, CR00017031, CR00017036

Models: AT-WA1104G-10

1 99
Download 99 pages 28.11 Kb
Page 46
Image 46

 

 

 

 

 

 

 

Features in 291-05

 

 

 

46

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR

Module

Level

Description

AR400

AR7x5

AR7x0S

 

Rapier i

AT8800-

AT-8600

 

AT-8700XL

x90048-

AT-9900

AT-9800

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00016940

Core

2

Some versions of the AT-G8T GBIC prevented the switch from detecting and

-

-

-

 

-

-

Y

 

-

-

-

-

 

 

 

setting up the AT-A47 expansion board correctly. This issue occurred on start-up

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

when the GBIC was installed and had a link up.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This issue has been resolved.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00016941

IP Gateway

2

When there were multiple routes to a destination and the best route was deleted

-

-

-

 

Y

Y

Y

 

Y

Y

Y

Y

 

 

 

from the switch’s hardware routing table, the switch did not use the alternative

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

route. Also, the switch only used the best route, even if ECMP was supported.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This issue has been resolved. When multiple routes exist and the best route is

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

deleted from the hardware table, the switch now adds the next best route to the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

hardware table correctly. If the switch supports ECMP, all routes are now added

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

to hardware, not just the best route.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00017006

Switch

2

Previously, the link to the AT-G8T GBIC would not come up automatically when

-

-

-

 

-

-

-

 

-

-

-

Y

 

 

 

its auto-negotiation slide switch was set to “on”. This was because the switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

configured the GBIC in a fixed speed mode by default.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This issue has been resolved. The link now comes up automatically when the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

auto-negotiation slide switch is set to “on”. To bring the link up when auto-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

negotiation is set to “off”, use the command:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

set swi port=port-listspeed=1000mf

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00017031

IGMP

2

If a port on the router or switch joined and left many IP multicast groups, the

Y

-

Y

 

Y

Y

Y

 

Y

Y

Y

Y

 

Snooping

 

router or switch sometimes did not transmit all multicast packets to all receivers.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This issue has been resolved.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00017036

Switch

2

In some trunk configurations, the STP state of trunks was incorrectly applied to

-

-

-

 

-

-

-

 

-

Y

Y

-

 

 

 

non-trunk ports. This could result in incorrect traffic flows in the network. This

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

issue has been resolved.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Version 291-10

C613-10488-00 REV G

Page 46
Image 46
Allied Telesis AT-WA1104G-10 manual CR00016940, CR00016941, CR00017006, CR00017031, CR00017036