Features in 291-04

 

 

 

78

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR

Module

Level

Description

AR400

AR7x5

AR7x0S

 

Rapier i

AT8800-

AT-8600

 

AT-8700XL

x90048-

AT-9900

AT-9800

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00013463

Ping

4

Previously, if you used the ? or Tab keys to obtain help about the timeout

Y

Y

Y

 

Y

Y

Y

 

Y

Y

Y

Y

 

 

 

parameter for the ping command, the resulting help said that the maximum

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

timeout was 65535. However, the correct maximum is 60 seconds.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This issue has been resolved. The “?” help now displays the correct range of

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

values.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00013589

Install

4

When a router or switch was using a trial licence for release software and the trial

Y

Y

Y

 

Y

Y

Y

 

Y

Y

Y

Y

 

 

 

period elapsed, the router or switch rebooted without indicating the reason for

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the reboot.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This issue has been resolved. The following error messages now explain why the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

router or switch is rebooting:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ERROR: There are no valid licences available for the current software release.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The device will now reboot.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ERROR: The trial licence for the current software release has expired.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The device will now reboot.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00013640

NTP

4

Output of the command show ntp displays a “Host Address” field. This is the

Y

Y

Y

 

Y

Y

Y

 

Y

Y

Y

Y

 

 

 

address of the interface from which the router or switch sends NTP packets.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Previously, if the IP address changed, the “Host Address” field did not change,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

even though NTP used the new address.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This issue has been resolved.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CR00014106

Core

4

If the router or switch runs a configuration file on start-up that contains the

Y

Y

Y

 

Y

Y

Y

 

Y

Y

Y

Y

 

 

 

command set summertime before the command enable summertime, a log

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

message on start-up says that summertime needs to be enabled. However,

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

summertime is correctly applied to the router or switch.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Previously, if you configured summertime then saved the configuration by using

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the command create config, set summertime came before enable

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

summertime in the resulting configuration file.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This issue has been resolved. When you save the configuration, enable

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

summertime now comes before set summertime in the resulting configuration

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

file, so the log message is not produced.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Version 291-10

C613-10488-00 REV G

Page 78
Image 78
Allied Telesis AT-WA1104G-10 manual CR00013463, CR00013589, CR00013640, CR00014106