Alpine IVA-W502E owner manual Auxiliary Device Optional, TUE-T200DVB Operation Optional, 54-EN

Auxiliary Device (Optional)

Operating Auxiliary Devices (Optional)

To operate your devices connected to the AUX terminals on the rear panel of IVA-W502E (AUX mode) or to the iPod Direct connector by using iPod Direct/RCA Interface cable (sold separately) (AUX+ mode), follow the procedure described below.

WARNING

It is dangerous (and illegal in many states) for the driver to watch the TV/Video while driving the vehicle. The driver may be distracted from looking ahead and an accident could occur.

Install the IVA-W502E correctly so that the driver cannot watch TV/Video unless the vehicle is stopped and the emergency brake is applied.

If the IVA-W502E is not installed correctly, the driver will be able to watch the TV/Video while driving the vehicle and may be distracted from looking ahead and cause an accident. The driver or other people could be severely injured.

•If you try to activate the auxiliary device while driving, the display will show the warning-PICTURE OFF FOR YOUR SAFETY.

1 Touch [SOURCE] on the main source screen.

The source screen appears on the display.

2 Touch [AUX]*1 or [AUX+]*2.

The external input screen is displayed.

3 Touch [NTSC/PAL] to change the video input.

4 Touch [COMP. /S-VIDEO]*3to switch the video signal input mode.

The mode switches with each touch.

*1 The name which is given as the source name in “Setting the AUX Mode” on page 36 is displayed.

*2 The mode which is given as the source name in “Setting the AUX+ Mode” (page 37).

*3 The video signal can be input in two ways, selecting the right mode depending on the connection method. Switching to the COMP. mode when using the Video Input Connector. Switching to the S-VIDEO mode when using the S Video Input Connector.

•If the AUX mode is not displayed on the main menu, set AUX IN to ON by following “Setting the AUX Mode” (page 36).

•The setting of switching NTSC/PAL, which you have set in this section can be used in same way in “Switching the Visual Input Signal System” on page 36.

•The display mode changes by touching [WIDE].

For operation, refer to “Switching Display Modes” on page 26.

•After connecting the KCA-410C, its AUX input can be used only in INTERRUPT MODE. For details, refer to the KCA-410C Owner’s Manual.

TUE-T200DVB Operation (Optional)

Operating the TUE-T200DVB (Optional)

Operable when optional TUE-T200DVB is connected.

When DVB-T is selected in “Setting the AUX Mode” (page 36), the source is displayed in SOURCE selection screen.

1 While your vehicle is parked, touch [SOURCE] on the main source screen.

The source screen appears on the display.

2 Touch [DVB-T].

The DVB-T screen is displayed.

3 Perform the desired operation.

Channel Number Up/Down or favourite Channel Number Up/Down

Touch [CH.]* to select changing the Channel or the favourite Channel.

Touch CH. [ ] or [ ] to move the Channel number Up/ Down.

Touch FAV [ ] or [ ] to move the favourite Channel number Up/Down.

* The button displays the current changing mode ([CH.] or [FAV]).

Calling up Main Menu Screen

Touch [MENU] to call up the main menu screen.

Calling up Menu Operation Mode

1 Touch [P1/2].

The function guide appears.

2 Touch [MENU CONT] to call up the menu operation mode.

Switching the Source

Touch [BAND].

The source switches with each touch.

Calling up Electronic Programme Guide (EPG)

Touch [EPG] to call up the Electronic Programme Guide.

Scanning Mode

1 Touch [P1/2].

The function guide appears.

2 Touch [A.MEMO] to start the auto scan procedure.

•For detail, refer to the Owner’s Manual of the TUE-T200DVB sold separately.

Switching the Video Input Mode

Touch [COMP./S-VIDEO].

The video signal input mode switches with each touch.

•Switching to the COMP. mode when using the Video Input Connector. Switching to the S-VIDEO mode when using the S Video Input Connector.

54-EN