Sail Switch Assembly Gas Models Only | American Dryer Corp AD-95

4.Remove bracket assembly by slightly sliding bracket toward the rear of the dryer and to the left.

5.Disconnect sensor bracket harness connector and remove bracket assembly from dryer.

6.Disconnect the two (2) orange wires from the thermostat.

7.Disassemble thermostat from bracket assembly by removing the two (2) mounting screws, washers and nuts.

8.Reverse this procedure for installing a hi-heat protector thermostat.

9.Reestablish power to the dryer.

D. Sail Switch Assembly (Gas Models Only)

The sail switch is a heat circuit safety device which controls the burner circuit only. When the dryer is operating and there is proper airflow, the sail switch damper pulls in and closes the sail switch. Providing all the other heat- related circuits are functioning properly, ignition should now be established. If an improper airflow occurs, the sail switch damper will release, and the circuit will open.

To Replace Sail Switch

1.Discontinue power to dryer.

2.Remove the two (2) screws which hold the sail switch box cover to sail switch box.

3.Disconnect the two (2) wires from the switch.

4.Disassemble sail switch from mounting bracket by removing the two (2) screws securing switch in place.

5.Reverse this procedure for installing new sail switch. Adjust sail switch described in the next section.

To Adjust Sail Switch

With the dryer operating at a high temperature setting, pull the sail switch away from the burner. The sail switch should open and extinguish the burner. Let the sail switch damper return to the burner wall. The sail switch should close to restart the burner ignition cycle. If the sail switch circuit does not operate as described, bend the actuator arm of the sail switch accordingly until proper operation is achieved. To check proper "open" position of sail switch, open main door, manually depress main door switch and start dryer. With the main door open and the dryer operating, the sail switch should be open, and the burner should not come on.

24

Image 28

American Dryer Corp AD-95 Sail Switch Assembly Gas Models Only, To Replace Sail Switch, To Adjust Sail Switch

Contents

AD-95/ML-95 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Content Troubleshooting Safety Precautions Section Cleaning WeeklyDays Months Seven Days after Installation and every 6 Months AdjustmentsLubrication Enclosure, Air Supply, and Exhaust Requirements Electrical and Gas Requirements Operational Service Check Procedure Prior to February 11 Control Panel Microprocessor As of February 11 With circuit breaker Reversing Relay Panel With fuses Gas Burner Assembly HSI Module Gas Models Drive Motor Blower Motor and Impeller Taperlock Trantorque Drive Shaft Assembly Idler Shaft Assembly Transtorque Taperlock Main Door Switch Basket Tumbler Sail Switch Gas Models Only Hi-Limit Gas Models Only Automatic Reset Thermostat Lint Screen Lint Drawer Switch Servicing Computer Controls To Replace Keyboard Label Assembly To Remove Flame Sensor Probe Ignition ControlsHSI Ignitor Flame Sensor Probe To Replace Gas Valve See burner illustration on To Test and Adjust Gas Water Column PressureTo Replace Main Burner Orifices To Convert Natural Gas to L.P. Gas To Replace Burner Tubes Discontinue power to the dryer To Replace HSI Module To Replace Sail Switch Sail Switch Assembly Gas Models OnlyTo Adjust Sail Switch To Replace Main Door Switch To Replace Main Door AssemblyTo Install New Main Door Glass as of October 24 Front Panel and Main Door Assemblies As of October 24 Prior to October 24 To Replace Front Panel To Install new Main Door Glass prior of October 24To Replace Main Door Hinge Block Pulleys To Replace Drive Shaft Pulley To Replace Drive Motor PulleyPage Tumbler Wheel Replacement on IdlerAssembly taper lock models Tumbler Wheel Replacement on IdlerAssembly trantorque models To Replace Blower Shaft Pulley Basket Assembly To Replace Blower Motor Pulley Belt Adjustment Motor to Drive Axle To Replace Drive Assembly Pillow Block BearingTo Replace Idler Shaft Pillow Block Bearing Motors To Replace Drive Motor V-BeltsTo Replace Impeller Motor Fan Shaft Drive To Replace Blower Motor V-belts To Replace Front Thruster Wheels Rear Access Impeller To Replace Lint Door Switch Lint Screen AssemblyTo Replace Lint Screen No display on computer Computer will not accept key pad entriesDryer will not start, but computer display indictors are on Drive motor runs, burner is on, but basket will not turn Thermal overload for drive motor is tripping Burner hi-limit safety thermostat is trippingOverload for impeller fan motor is tripping There is excessive vibration coming from the basket Phase 6 OPL System Diagnostics Page E.D. Display Indicators E.D Display Indicator Number AIR AIR JET Output L.E.D. Indicator Optional FAN Blower Output L.E.D. Indicator Fuse Main Fuse Input L.E.D. Indicator Flame bURNER Control Fail Input L.E.D. Indicator E.D. Codes BURNER Safety Fail DRUM Safety FailBURNER Control Fail BURNER Flame Fail Computer Logic and Wiring Diagram No Display Condition Drive motor reverses but does not forward, blower motor runs Blower motor does not operate, drive motor runs Lint Door Condition Main Door Condition Microprocessor Which Must be Reset Manually Technical Information For example Data Label HOW to USE a Manometer AD-95/ML-95 Tool List ADC450188 1- 01/14/99-25