To Replace Keyboard Label Assembly | American Dryer Corp AD-95

To Replace Keyboard Label Assembly

1.Discontinue power to dryer.

2.Unplug keyboard ribbon from rear of computer.

3.Slowly peel off and remove keyboard label assembly from control panel.

4.Peel paper backing off new keyboard label assembly.

5.Holding the new keyboard label assembly close to the panel, insert the keyboard ribbon through the rectangular slot in the control panel. Align label assembly into

position by matching the red viewing window on the label to the rectangular cutout in the panel and gently press into place.

6.Connect keyboard ribbon to the computer.

7.Reestablish power to dryer.

To Replace Microprocessor Temperature Sensor

Probe

1. Discontinue power to the dryer.

2. Open lint door.

3. Remove microprocessor sensor bracket assembly from dryer.

a. Disconnect sensor bracket harness connector. b. Loosen the two (2) Phillips head screws which secure bracket assembly to dryer and remove

bracket from dryer.

NOTE: Do not remove screws.

4.Disassemble sensor probe from bracket assembly by removing the top push-on fastener securing the probe from bracket. Use a small screwdriver to slowly pry the fastener off.

5.Disconnect the two (2) orange wires from the high heat (225º F) thermostat, and remove modular bracket connector, wires, and probe from bracket assembly.

6.Install new sensor probe assembly (ADC P/N 811710) by reversing procedure.

7.Reestablish power to the dryer.

NOTE: If, when power is reestablished, the computer display reads "TEMP SENSOR FAIL CHECK TEMP SENSOR FUSE," check for a loose connection in the wiring.

19

Image 23

American Dryer Corp AD-95 service manual To Replace Keyboard Label Assembly

Contents

AD-95/ML-95 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Content Troubleshooting Section Safety Precautions Months CleaningWeekly Days Lubrication AdjustmentsSeven Days after Installation and every 6 Months Electrical and Gas Requirements Enclosure, Air Supply, and Exhaust Requirements Operational Service Check Procedure As of February 11 Prior to February 11 Control Panel Microprocessor With fuses With circuit breaker Reversing Relay Panel HSI Module Gas Models Gas Burner Assembly Blower Motor and Impeller Drive Motor Taperlock Trantorque Drive Shaft Assembly Transtorque Taperlock Idler Shaft Assembly Basket Tumbler Main Door Switch Hi-Limit Gas Models Only Sail Switch Gas Models Only Lint Screen Automatic Reset Thermostat Lint Drawer Switch Computer Controls Servicing To Replace Keyboard Label Assembly HSI Ignitor Flame Sensor Probe Ignition ControlsTo Remove Flame Sensor Probe To Replace Main Burner Orifices To Test and Adjust Gas Water Column PressureTo Replace Gas Valve See burner illustration on To Replace Burner Tubes To Convert Natural Gas to L.P. Gas To Replace HSI Module Discontinue power to the dryer To Adjust Sail Switch Sail Switch Assembly Gas Models OnlyTo Replace Sail Switch Front Panel and Main Door Assemblies To Replace Main Door SwitchTo Replace Main Door Assembly To Install New Main Door Glass as of October 24 As of October 24 Prior to October 24 To Replace Main Door Hinge Block To Install new Main Door Glass prior of October 24To Replace Front Panel To Replace Drive Motor Pulley Pulleys To Replace Drive Shaft PulleyPage Tumbler Wheel Replacement on IdlerAssembly taper lock models To Replace Blower Shaft Pulley Tumbler Wheel Replacement on IdlerAssembly trantorque models To Replace Blower Motor Pulley Basket Assembly To Replace Idler Shaft Pillow Block Bearing To Replace Drive Assembly Pillow Block BearingBelt Adjustment Motor to Drive Axle To Replace Impeller Motor Fan Shaft Drive To Replace Drive Motor V-BeltsMotors To Replace Front Thruster Wheels To Replace Blower Motor V-belts Impeller Rear Access To Replace Lint Screen Lint Screen AssemblyTo Replace Lint Door Switch Drive motor runs, burner is on, but basket will not turn No display on computerComputer will not accept key pad entries Dryer will not start, but computer display indictors are on Overload for impeller fan motor is tripping Burner hi-limit safety thermostat is trippingThermal overload for drive motor is tripping There is excessive vibration coming from the basket Phase 6 OPL System Diagnostics Page E.D. Display Indicators E.D Display Indicator Number FAN Blower Output L.E.D. Indicator AIR AIR JET Output L.E.D. Indicator Optional Fuse Main Fuse Input L.E.D. Indicator Flame bURNER Control Fail Input L.E.D. Indicator E.D. Codes BURNER Flame Fail BURNER Safety FailDRUM Safety Fail BURNER Control Fail Computer Logic and Wiring Diagram No Display Condition Blower motor does not operate, drive motor runs Drive motor reverses but does not forward, blower motor runs Main Door Condition Lint Door Condition Microprocessor Which Must be Reset Manually For example Technical Information Data Label HOW to USE a Manometer AD-95/ML-95 Tool List ADC450188 1- 01/14/99-25