To Replace Front Panel | American Dryer Corp AD-95 instruction

7.The door assembly should now be put in an area where it will not be disturbed for a few hours. This will give the silicone a chance to harden.

NOTE: Once the silicone is cured you may want to trim any excess silicone on the inside of the main door assembly.

8. After the curing period install the main door on the dryer by reversing step no. 1.

To Install new Main Door Glass prior of October 24, 1997

1.Remove main door assembly from dryer (follow main door removal procedure).

2.Lay main door on flat surface with back of door face down.

3.Remove glass and clean all old sealant off main door. This area must be completely clean for correct bonding.

4.Apply a narrow bead of silicone (ADC P/N 170730) all around main door area where glass will rest.

5.Install glass onto door and adhesive. Slightly press glass into place.

IMPORTANT: Do not press hard or silicone thickness between the glass and door will be reduced, resulting in poor bonding.

NOTE: Once the silicone is cured you may want to trim any excess silicone on the inside of the main door assembly.

6. After the curing period install the main door on the dryer by reversing step #1.

To Replace Front Panel

1.Discontinue power to dryer.

2.Remove bottom lint door assembly.

3.Disconnect the four emergency stop wires located in the front left electrical box.

4.Remove the front panel by removing the screws.

IMPORTANT: When pulling the front panel off, the door switch harness in the upper right hand corner must be unplugged.

NOTE: The main door assembly can be removed to make the panel removal easier. Refer to "replace main door assembly" directions.

5.Disconnect the emergency stop assembly from the old panel and reinstall on the new panel.

6.Disconnect other door switch wiring switch from the old panel and reinstall on the new front panel.

7.Reinstall the new front panel by reversing steps 1 through 3.

8.Reestablish power to dryer.

To Replace Main Door Hinge Block

1.Discontinue power to dryer.

2.Follow procedure for removal of main door assembly for top hinge removal.

3.Remove the two screws from the bottom hinge block.

4.Reassemble by reversing removal procedure.

27

Image 31

American Dryer Corp AD-95 service manual To Replace Front Panel, To Replace Main Door Hinge Block

Contents

AD-95/ML-95 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Content Troubleshooting Section Safety Precautions Months CleaningWeekly Days Seven Days after Installation and every 6 Months AdjustmentsLubrication Electrical and Gas Requirements Enclosure, Air Supply, and Exhaust Requirements Operational Service Check Procedure As of February 11 Prior to February 11 Control Panel Microprocessor With fuses With circuit breaker Reversing Relay Panel HSI Module Gas Models Gas Burner Assembly Blower Motor and Impeller Drive Motor Taperlock Trantorque Drive Shaft Assembly Transtorque Taperlock Idler Shaft Assembly Basket Tumbler Main Door Switch Hi-Limit Gas Models Only Sail Switch Gas Models Only Lint Screen Automatic Reset Thermostat Lint Drawer Switch Computer Controls Servicing To Replace Keyboard Label Assembly To Remove Flame Sensor Probe Ignition ControlsHSI Ignitor Flame Sensor Probe To Replace Gas Valve See burner illustration on To Test and Adjust Gas Water Column PressureTo Replace Main Burner Orifices To Replace Burner Tubes To Convert Natural Gas to L.P. Gas To Replace HSI Module Discontinue power to the dryer To Replace Sail Switch Sail Switch Assembly Gas Models OnlyTo Adjust Sail Switch Front Panel and Main Door Assemblies To Replace Main Door SwitchTo Replace Main Door Assembly To Install New Main Door Glass as of October 24 As of October 24 Prior to October 24 To Replace Front Panel To Install new Main Door Glass prior of October 24To Replace Main Door Hinge Block To Replace Drive Motor Pulley Pulleys To Replace Drive Shaft PulleyPage Tumbler Wheel Replacement on IdlerAssembly taper lock models To Replace Blower Shaft Pulley Tumbler Wheel Replacement on IdlerAssembly trantorque models To Replace Blower Motor Pulley Basket Assembly Belt Adjustment Motor to Drive Axle To Replace Drive Assembly Pillow Block BearingTo Replace Idler Shaft Pillow Block Bearing Motors To Replace Drive Motor V-BeltsTo Replace Impeller Motor Fan Shaft Drive To Replace Front Thruster Wheels To Replace Blower Motor V-belts Impeller Rear Access To Replace Lint Door Switch Lint Screen AssemblyTo Replace Lint Screen Drive motor runs, burner is on, but basket will not turn No display on computerComputer will not accept key pad entries Dryer will not start, but computer display indictors are on Thermal overload for drive motor is tripping Burner hi-limit safety thermostat is trippingOverload for impeller fan motor is tripping There is excessive vibration coming from the basket Phase 6 OPL System Diagnostics Page E.D. Display Indicators E.D Display Indicator Number FAN Blower Output L.E.D. Indicator AIR AIR JET Output L.E.D. Indicator Optional Fuse Main Fuse Input L.E.D. Indicator Flame bURNER Control Fail Input L.E.D. Indicator E.D. Codes BURNER Flame Fail BURNER Safety FailDRUM Safety Fail BURNER Control Fail Computer Logic and Wiring Diagram No Display Condition Blower motor does not operate, drive motor runs Drive motor reverses but does not forward, blower motor runs Main Door Condition Lint Door Condition Microprocessor Which Must be Reset Manually For example Technical Information Data Label HOW to USE a Manometer AD-95/ML-95 Tool List ADC450188 1- 01/14/99-25