Front Panel and Main Door Assemblies | American Dryer Corp AD-95

CAUTION: Do not abort this switch by taping or screwing sail switch damper to burner. PERSONAL INJURY OR FIRE COULD RESULT.

E. Front Panel and Main Door Assemblies

To Replace Main Door Switch

1.Discontinue power to dryer.

2.Open main door.

3.Remove the two (2) Phillips head screws holding the main door switch bracket assembly in place.

4.Disconnect wiring from switch assembly.

5.Reverse this procedure for installing new door switch assembly.

6.Reestablish power to dryer.

IMPORTANT: Under no circumstances should the door switch be disabled.

To Replace Main Door Assembly

1.Open main door.

2.Holding the door upward remove the two (2) screws from the top hinge block.

3.Lift the door up to remove.

4.Reverse this procedure for reinstalling new main door assembly.

To Install New Main Door Glass as of October 24, 1997

1.Remove main door assembly from dryer (follow main door removal procedure).

2.Lay main door on flat surface with the back of the door facing down.

3.Remove the four 10-32 acorn nuts securing the glass to the door.

4.Remove glass and clean all old sealant off main door. This area must be clean for correct bonding.

5.Place a bead of silicone around the edge door and lightly press glass into place.

25

Image 29

American Dryer Corp AD-95 Front Panel and Main Door Assemblies, To Replace Main Door Switch, To Replace Main Door Assembly

Contents

AD-95/ML-95 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Content Troubleshooting Section Safety Precautions Weekly CleaningDays Months Lubrication AdjustmentsSeven Days after Installation and every 6 Months Electrical and Gas Requirements Enclosure, Air Supply, and Exhaust Requirements Operational Service Check Procedure As of February 11 Prior to February 11 Control Panel Microprocessor With fuses With circuit breaker Reversing Relay Panel HSI Module Gas Models Gas Burner Assembly Blower Motor and Impeller Drive Motor Taperlock Trantorque Drive Shaft Assembly Transtorque Taperlock Idler Shaft Assembly Basket Tumbler Main Door Switch Hi-Limit Gas Models Only Sail Switch Gas Models Only Lint Screen Automatic Reset Thermostat Lint Drawer Switch Computer Controls Servicing To Replace Keyboard Label Assembly HSI Ignitor Flame Sensor Probe Ignition ControlsTo Remove Flame Sensor Probe To Replace Main Burner Orifices To Test and Adjust Gas Water Column PressureTo Replace Gas Valve See burner illustration on To Replace Burner Tubes To Convert Natural Gas to L.P. Gas To Replace HSI Module Discontinue power to the dryer To Adjust Sail Switch Sail Switch Assembly Gas Models OnlyTo Replace Sail Switch To Replace Main Door Assembly To Replace Main Door SwitchTo Install New Main Door Glass as of October 24 Front Panel and Main Door Assemblies As of October 24 Prior to October 24 To Replace Main Door Hinge Block To Install new Main Door Glass prior of October 24To Replace Front Panel To Replace Drive Motor Pulley Pulleys To Replace Drive Shaft PulleyPage Tumbler Wheel Replacement on IdlerAssembly taper lock models To Replace Blower Shaft Pulley Tumbler Wheel Replacement on IdlerAssembly trantorque models To Replace Blower Motor Pulley Basket Assembly To Replace Idler Shaft Pillow Block Bearing To Replace Drive Assembly Pillow Block BearingBelt Adjustment Motor to Drive Axle To Replace Impeller Motor Fan Shaft Drive To Replace Drive Motor V-BeltsMotors To Replace Front Thruster Wheels To Replace Blower Motor V-belts Impeller Rear Access To Replace Lint Screen Lint Screen AssemblyTo Replace Lint Door Switch Computer will not accept key pad entries No display on computerDryer will not start, but computer display indictors are on Drive motor runs, burner is on, but basket will not turn Overload for impeller fan motor is tripping Burner hi-limit safety thermostat is trippingThermal overload for drive motor is tripping There is excessive vibration coming from the basket Phase 6 OPL System Diagnostics Page E.D. Display Indicators E.D Display Indicator Number FAN Blower Output L.E.D. Indicator AIR AIR JET Output L.E.D. Indicator Optional Fuse Main Fuse Input L.E.D. Indicator Flame bURNER Control Fail Input L.E.D. Indicator E.D. Codes DRUM Safety Fail BURNER Safety FailBURNER Control Fail BURNER Flame Fail Computer Logic and Wiring Diagram No Display Condition Blower motor does not operate, drive motor runs Drive motor reverses but does not forward, blower motor runs Main Door Condition Lint Door Condition Microprocessor Which Must be Reset Manually For example Technical Information Data Label HOW to USE a Manometer AD-95/ML-95 Tool List ADC450188 1- 01/14/99-25