As of October 24 Prior to October 24 | American Dryer Corp AD-95

IMPORTANT: Do not press hard or silicone thickness between the glass and door will be reduced, resulting in poor bonding.

6.The door assembly should now be put in an area where it will not be disturbed for at least 24 hours. Depending on the conditions, the curing time of this adhesive is 24 to 36 hours.

7.After 24-hour curing period, install main door on dryer by reversing step 1.

IMPORTANT: Do not press hard or silicone thickness between the glass and door will be reduced, resulting in poor bonding.

6. Reinstall the four 10-32 acorn nuts that where removed in step #3.

As of October 24, 1997

Prior to October 24, 1997

26

Image 30

American Dryer Corp AD-95 service manual As of October 24 Prior to October 24

Contents

AD-95/ML-95 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Content Troubleshooting Safety Precautions Section Days CleaningWeekly Months Adjustments Seven Days after Installation and every 6 MonthsLubrication Enclosure, Air Supply, and Exhaust Requirements Electrical and Gas Requirements Operational Service Check Procedure Prior to February 11 Control Panel Microprocessor As of February 11 With circuit breaker Reversing Relay Panel With fuses Gas Burner Assembly HSI Module Gas Models Drive Motor Blower Motor and Impeller Taperlock Trantorque Drive Shaft Assembly Idler Shaft Assembly Transtorque Taperlock Main Door Switch Basket Tumbler Sail Switch Gas Models Only Hi-Limit Gas Models Only Automatic Reset Thermostat Lint Screen Lint Drawer Switch Servicing Computer Controls To Replace Keyboard Label Assembly Ignition Controls To Remove Flame Sensor ProbeHSI Ignitor Flame Sensor Probe To Test and Adjust Gas Water Column Pressure To Replace Gas Valve See burner illustration onTo Replace Main Burner Orifices To Convert Natural Gas to L.P. Gas To Replace Burner Tubes Discontinue power to the dryer To Replace HSI Module Sail Switch Assembly Gas Models Only To Replace Sail SwitchTo Adjust Sail Switch To Install New Main Door Glass as of October 24 To Replace Main Door SwitchTo Replace Main Door Assembly Front Panel and Main Door Assemblies As of October 24 Prior to October 24 To Install new Main Door Glass prior of October 24 To Replace Front PanelTo Replace Main Door Hinge Block Pulleys To Replace Drive Shaft Pulley To Replace Drive Motor PulleyPage Tumbler Wheel Replacement on IdlerAssembly taper lock models Tumbler Wheel Replacement on IdlerAssembly trantorque models To Replace Blower Shaft Pulley Basket Assembly To Replace Blower Motor Pulley To Replace Drive Assembly Pillow Block Bearing Belt Adjustment Motor to Drive AxleTo Replace Idler Shaft Pillow Block Bearing To Replace Drive Motor V-Belts MotorsTo Replace Impeller Motor Fan Shaft Drive To Replace Blower Motor V-belts To Replace Front Thruster Wheels Rear Access Impeller Lint Screen Assembly To Replace Lint Door SwitchTo Replace Lint Screen Dryer will not start, but computer display indictors are on No display on computerComputer will not accept key pad entries Drive motor runs, burner is on, but basket will not turn Burner hi-limit safety thermostat is tripping Thermal overload for drive motor is trippingOverload for impeller fan motor is tripping There is excessive vibration coming from the basket Phase 6 OPL System Diagnostics Page E.D. Display Indicators E.D Display Indicator Number AIR AIR JET Output L.E.D. Indicator Optional FAN Blower Output L.E.D. Indicator Fuse Main Fuse Input L.E.D. Indicator Flame bURNER Control Fail Input L.E.D. Indicator E.D. Codes BURNER Control Fail BURNER Safety FailDRUM Safety Fail BURNER Flame Fail Computer Logic and Wiring Diagram No Display Condition Drive motor reverses but does not forward, blower motor runs Blower motor does not operate, drive motor runs Lint Door Condition Main Door Condition Microprocessor Which Must be Reset Manually Technical Information For example Data Label HOW to USE a Manometer AD-95/ML-95 Tool List ADC450188 1- 01/14/99-25