Manuals / American Dryer Corp / Laundry Appliance / Washer/Dryer

American Dryer Corp AD-95 To Replace Blower Motor V-belts, To Replace Front Thruster Wheels

Models: AD-95

1 64

Download 64 pages 35.24 Kb

Page 39

5.Loosen the tension on the blower motor v-belts by loosening the jam nuts and then the adjustment bolt.

6.Remove the bolts securing the motor mount assembly to the dryer cabinet and remove the motor mount assembly from the dryer.

NOTE: The motor mount assembly will not be able to be removed to far due the wiring harness still connected.

7.Disconnect the wiring harness from motor.

8.Remove motor pulley from old motor and install on new motor.

NOTE: Be sure to take measurements of the pulley location on the old motor and in this way the belt will be aligned.

9.Remove the old motor from the motor mount and install the new motor on the mount.

10.Reconnect the wiring harness to the motor.

11.Install motor mount assembly back into the dryer and replace bolts into proper holes finger tight.

12.Replace belts and adjust belt tension.

NOTE: Be sure that the belt alignment is still proper.

13.Retighten bolts

14.Reestablish power to dryer.

To Replace Blower Motor V-belts

1.Remove the ten (10) 1/4 - 20 x 1/4" socket button head screws from the perforated basket side and remove the basket panel.

2.Remove the right side wrapper.

3.Remove the blower motor belt by loosening the 3/8" bolt with locking nuts.

4.Reinstall new belts by reversing steps 1 though 3.

To Replace Front Thruster Wheels

1. Discontinue power to the dryer.

35

Image 39

American Dryer Corp AD-95 service manual To Replace Blower Motor V-belts, To Replace Front Thruster Wheels

Contents

AD-95/ML-95 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Content Troubleshooting Section Safety PrecautionsMonths CleaningWeekly DaysAdjustments Seven Days after Installation and every 6 MonthsLubrication Electrical and Gas Requirements Enclosure, Air Supply, and Exhaust RequirementsOperational Service Check Procedure As of February 11 Prior to February 11 Control Panel MicroprocessorWith fuses With circuit breaker Reversing Relay PanelHSI Module Gas Models Gas Burner AssemblyBlower Motor and Impeller Drive MotorTaperlock Trantorque Drive Shaft Assembly Transtorque Taperlock Idler Shaft AssemblyBasket Tumbler Main Door SwitchHi-Limit Gas Models Only Sail Switch Gas Models OnlyLint Screen Automatic Reset ThermostatLint Drawer Switch Computer Controls ServicingTo Replace Keyboard Label Assembly Ignition Controls To Remove Flame Sensor ProbeHSI Ignitor Flame Sensor Probe To Test and Adjust Gas Water Column Pressure To Replace Gas Valve See burner illustration onTo Replace Main Burner Orifices To Replace Burner Tubes To Convert Natural Gas to L.P. GasTo Replace HSI Module Discontinue power to the dryerSail Switch Assembly Gas Models Only To Replace Sail SwitchTo Adjust Sail Switch Front Panel and Main Door Assemblies To Replace Main Door SwitchTo Replace Main Door Assembly To Install New Main Door Glass as of October 24As of October 24 Prior to October 24 To Install new Main Door Glass prior of October 24 To Replace Front PanelTo Replace Main Door Hinge Block To Replace Drive Motor Pulley Pulleys To Replace Drive Shaft PulleyPage Tumbler Wheel Replacement on IdlerAssembly taper lock models To Replace Blower Shaft Pulley Tumbler Wheel Replacement on IdlerAssembly trantorque modelsTo Replace Blower Motor Pulley Basket AssemblyTo Replace Drive Assembly Pillow Block Bearing Belt Adjustment Motor to Drive AxleTo Replace Idler Shaft Pillow Block Bearing To Replace Drive Motor V-Belts MotorsTo Replace Impeller Motor Fan Shaft Drive To Replace Front Thruster Wheels To Replace Blower Motor V-beltsImpeller Rear AccessLint Screen Assembly To Replace Lint Door SwitchTo Replace Lint Screen Drive motor runs, burner is on, but basket will not turn No display on computerComputer will not accept key pad entries Dryer will not start, but computer display indictors are onBurner hi-limit safety thermostat is tripping Thermal overload for drive motor is trippingOverload for impeller fan motor is tripping There is excessive vibration coming from the basket Phase 6 OPL System Diagnostics Page E.D. Display Indicators E.D Display Indicator Number FAN Blower Output L.E.D. Indicator AIR AIR JET Output L.E.D. Indicator OptionalFuse Main Fuse Input L.E.D. Indicator Flame bURNER Control Fail Input L.E.D. Indicator E.D. Codes BURNER Flame Fail BURNER Safety FailDRUM Safety Fail BURNER Control FailComputer Logic and Wiring Diagram No Display Condition Blower motor does not operate, drive motor runs Drive motor reverses but does not forward, blower motor runsMain Door Condition Lint Door ConditionMicroprocessor Which Must be Reset Manually For example Technical InformationData Label HOW to USE a Manometer AD-95/ML-95 Tool List ADC450188 1- 01/14/99-25