To Replace Blower Motor Pulley | American Dryer Corp AD-95 instruction

IMPORTANT: Tighten screws evenly and progressively. Never allow the sheave to be drawn in contact with the flange of the bushing. This gap should measure from 1/8" to 1/4". Proper cap screw torque is 30 ft-lbs. If greater tightening forces are applied, excess pressures will be created in the hub of the mounted sheave which may cause it to crack.

To Replace Blower Motor Pulley

1.Discontinue power to the dryer.

2.Remove the ten (10) 1/4 - 20 x 1/4" socket button head screws from the perforated basket side and remove the basket panel.

3.Remove the inside right wrapper.

4.Loosen v-belts, rotate pulley and roll v-belts out of groove.

5.Remove cap screws from the bushings.

6.Insert cap screws in tapped removal holes and tighten evenly until bushing becomes loose on shaft.

7.Remove bushing, pulley and key.

8.Reverse this procedure for replacement.

IMPORTANT: Tighten screws evenly and progressively. Never allow the sheave to be drawn in contact with the flange of the bushing. This gap should measure from 1/8" to 1/4". Proper cap screw torque is 30 ft-lbs. If greater tightening forces are applied, excess pressures will be created in the hub of the mounted sheave which may cause it to crack.

Basket Assembly

NOTE: Dryer must be level prior to basket alignment.

1.Discontinue power to the dryer.

2.Remove the perforated basket (tumbler) panel.

3.Remove wrapper panel to access the drive and idler shaft.

32

Image 36

American Dryer Corp AD-95 service manual To Replace Blower Motor Pulley, Basket Assembly

Contents

AD-95/ML-95 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Content Troubleshooting Safety Precautions Section Cleaning WeeklyDays Months Adjustments Seven Days after Installation and every 6 MonthsLubrication Enclosure, Air Supply, and Exhaust Requirements Electrical and Gas Requirements Operational Service Check Procedure Prior to February 11 Control Panel Microprocessor As of February 11 With circuit breaker Reversing Relay Panel With fuses Gas Burner Assembly HSI Module Gas Models Drive Motor Blower Motor and Impeller Taperlock Trantorque Drive Shaft Assembly Idler Shaft Assembly Transtorque Taperlock Main Door Switch Basket Tumbler Sail Switch Gas Models Only Hi-Limit Gas Models Only Automatic Reset Thermostat Lint Screen Lint Drawer Switch Servicing Computer Controls To Replace Keyboard Label Assembly Ignition Controls To Remove Flame Sensor ProbeHSI Ignitor Flame Sensor Probe To Test and Adjust Gas Water Column Pressure To Replace Gas Valve See burner illustration onTo Replace Main Burner Orifices To Convert Natural Gas to L.P. Gas To Replace Burner Tubes Discontinue power to the dryer To Replace HSI Module Sail Switch Assembly Gas Models Only To Replace Sail SwitchTo Adjust Sail Switch To Replace Main Door Switch To Replace Main Door AssemblyTo Install New Main Door Glass as of October 24 Front Panel and Main Door Assemblies As of October 24 Prior to October 24 To Install new Main Door Glass prior of October 24 To Replace Front PanelTo Replace Main Door Hinge Block Pulleys To Replace Drive Shaft Pulley To Replace Drive Motor PulleyPage Tumbler Wheel Replacement on IdlerAssembly taper lock models Tumbler Wheel Replacement on IdlerAssembly trantorque models To Replace Blower Shaft Pulley Basket Assembly To Replace Blower Motor Pulley To Replace Drive Assembly Pillow Block Bearing Belt Adjustment Motor to Drive AxleTo Replace Idler Shaft Pillow Block Bearing To Replace Drive Motor V-Belts MotorsTo Replace Impeller Motor Fan Shaft Drive To Replace Blower Motor V-belts To Replace Front Thruster Wheels Rear Access Impeller Lint Screen Assembly To Replace Lint Door SwitchTo Replace Lint Screen No display on computer Computer will not accept key pad entriesDryer will not start, but computer display indictors are on Drive motor runs, burner is on, but basket will not turn Burner hi-limit safety thermostat is tripping Thermal overload for drive motor is trippingOverload for impeller fan motor is tripping There is excessive vibration coming from the basket Phase 6 OPL System Diagnostics Page E.D. Display Indicators E.D Display Indicator Number AIR AIR JET Output L.E.D. Indicator Optional FAN Blower Output L.E.D. Indicator Fuse Main Fuse Input L.E.D. Indicator Flame bURNER Control Fail Input L.E.D. Indicator E.D. Codes BURNER Safety Fail DRUM Safety FailBURNER Control Fail BURNER Flame Fail Computer Logic and Wiring Diagram No Display Condition Drive motor reverses but does not forward, blower motor runs Blower motor does not operate, drive motor runs Lint Door Condition Main Door Condition Microprocessor Which Must be Reset Manually Technical Information For example Data Label HOW to USE a Manometer AD-95/ML-95 Tool List ADC450188 1- 01/14/99-25