E.D. Display Indicators | American Dryer Corp AD-95 specification

NOTE: RPM- This routine monitors the timing response from the existing rotational sensor input and derives a RPM measurement. To display this RPM measurement (press the "ENTER/START" key once and release, then press the "ENTER/START" key a second time and hold. This will display the RPM measurement). The rotational sensor must be active for operation of this fea- ture.

12.CHECK MAIN FUSE- Indicates that the circuit fuse protection which is located on the back side of the Phase 6 microprocessor controller (computer) the display would read "CHECK MAIN FUSE." If the display continues after the fuse has been replaced then it is the fault of the Phase 6 microproces- sor controller (computer).

B.L.E.D. DISPLAY INDICATORS

The L.E.D. indicator dots located on the top portion of the display indicates various Phase 6 OPL computer output functions while a cycle is in progress. These indicator dots (as shown in the illustration below) do not necessarily mean that the outputs are functioning. They are only indicating that the function output should be active (on).

1.L.E.D. DISPLAY INDICATOR NUMBER 1

a. For Optional Reversing Models:

1.This indicator dot is on when the drive (basket [tumbler]) motor is operating in the forward mode (clockwise direction).

2.L.E.D. DISPLAY INDICATOR NUMBER 2

a.For Optional Reversing Models:

1.This indicator dot is on when the drive (basket [tumbler]) motor is operating in the reverse mode (counterclockwise direction).

3.L.E.D. DISPLAY INDICATOR NUMBER 3

a.Heat Circuit Indicator:

1.This indicator dot is on whenever the Phase 6 OPL microprocessor controller (computer) is calling for the heating circuit to be active (on).

4.L.E.D DISPLAY INDICATOR NUMBER 4

a.On Indicator:

1.This indicator dot is on whenever a cycle is in progress. Additionally, when the Anti-Wrinkle program is active, the indicator dot will be on whenever the Phase 6 OPL microprocessor controller (computer) is in the Guard On Time program.

43

Image 47

American Dryer Corp AD-95 service manual E.D. Display Indicators

Contents

AD-95/ML-95 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Content Troubleshooting Section Safety Precautions Months CleaningWeekly Days Lubrication AdjustmentsSeven Days after Installation and every 6 Months Electrical and Gas Requirements Enclosure, Air Supply, and Exhaust Requirements Operational Service Check Procedure As of February 11 Prior to February 11 Control Panel Microprocessor With fuses With circuit breaker Reversing Relay Panel HSI Module Gas Models Gas Burner Assembly Blower Motor and Impeller Drive Motor Taperlock Trantorque Drive Shaft Assembly Transtorque Taperlock Idler Shaft Assembly Basket Tumbler Main Door Switch Hi-Limit Gas Models Only Sail Switch Gas Models Only Lint Screen Automatic Reset Thermostat Lint Drawer Switch Computer Controls Servicing To Replace Keyboard Label Assembly HSI Ignitor Flame Sensor Probe Ignition ControlsTo Remove Flame Sensor Probe To Replace Main Burner Orifices To Test and Adjust Gas Water Column PressureTo Replace Gas Valve See burner illustration on To Replace Burner Tubes To Convert Natural Gas to L.P. Gas To Replace HSI Module Discontinue power to the dryer To Adjust Sail Switch Sail Switch Assembly Gas Models OnlyTo Replace Sail Switch Front Panel and Main Door Assemblies To Replace Main Door SwitchTo Replace Main Door Assembly To Install New Main Door Glass as of October 24 As of October 24 Prior to October 24 To Replace Main Door Hinge Block To Install new Main Door Glass prior of October 24To Replace Front Panel To Replace Drive Motor Pulley Pulleys To Replace Drive Shaft PulleyPage Tumbler Wheel Replacement on IdlerAssembly taper lock models To Replace Blower Shaft Pulley Tumbler Wheel Replacement on IdlerAssembly trantorque models To Replace Blower Motor Pulley Basket Assembly To Replace Idler Shaft Pillow Block Bearing To Replace Drive Assembly Pillow Block BearingBelt Adjustment Motor to Drive Axle To Replace Impeller Motor Fan Shaft Drive To Replace Drive Motor V-BeltsMotors To Replace Front Thruster Wheels To Replace Blower Motor V-belts Impeller Rear Access To Replace Lint Screen Lint Screen AssemblyTo Replace Lint Door Switch Drive motor runs, burner is on, but basket will not turn No display on computerComputer will not accept key pad entries Dryer will not start, but computer display indictors are on Overload for impeller fan motor is tripping Burner hi-limit safety thermostat is trippingThermal overload for drive motor is tripping There is excessive vibration coming from the basket Phase 6 OPL System Diagnostics Page E.D. Display Indicators E.D Display Indicator Number FAN Blower Output L.E.D. Indicator AIR AIR JET Output L.E.D. Indicator Optional Fuse Main Fuse Input L.E.D. Indicator Flame bURNER Control Fail Input L.E.D. Indicator E.D. Codes BURNER Flame Fail BURNER Safety FailDRUM Safety Fail BURNER Control Fail Computer Logic and Wiring Diagram No Display Condition Blower motor does not operate, drive motor runs Drive motor reverses but does not forward, blower motor runs Main Door Condition Lint Door Condition Microprocessor Which Must be Reset Manually For example Technical Information Data Label HOW to USE a Manometer AD-95/ML-95 Tool List ADC450188 1- 01/14/99-25