To Replace Drive Motor V-Belts, Motors | American Dryer Corp AD-95

8.Retighten motor mount bolts and jam nuts.

9.Assemble front panel lint door assemblies back to dryer.

10.Reestablish power to dryer.

To Replace Drive Motor V-Belts

1.Discontinue power to the dryer.

2.Remove front panel. Follow front panel replacement instructions on page 27.

3.Loosen tension on v-belt so that it can easily be rolled off pulley. This can be done by loosening the four bolts holding the motor to the side of the dryer. As well as the adjustment bolt on top.

4.Replace v-belt.

5.Retighten v-belt and adjust tension and alignment per previous instructions.

J. Motors

To Replace Drive Motor

1. Discontinue power to dryer.

2. Remove front panel from dryer. Follow front panel replacement instructions on page 27.

3. Remove drive belt.

4. Disconnect wiring harness from motor.

5. Remove bolts holding motor to mount and replace with new motor. Do not tighten bolts.

6. Remove pulley from old motor and install on new motor. By removing the set screw from the drive motor pulley.

NOTE: A gear puller may be required to remove pulley.

7.Align motor pulley with drive assembly pulley and tighten set screw holding motor pulley.

8.Replace belts and adjust belt tension.

9.Retighten bolts.

10.Reestablish power to dryer.

To Replace Impeller Motor (Fan Shaft Drive)

1.Discontinue power to the dryer.

2.Remove lint door and front panel from dryer.

3.Remove the perforated panel inside the basket (tumbler).

4.Remove the wrapper assembly under the basket.

34

Image 38

American Dryer Corp AD-95 service manual To Replace Drive Motor V-Belts, Motors, To Replace Impeller Motor Fan Shaft Drive

Contents

AD-95/ML-95 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Content Troubleshooting Safety Precautions Section Days CleaningWeekly Months Lubrication AdjustmentsSeven Days after Installation and every 6 Months Enclosure, Air Supply, and Exhaust Requirements Electrical and Gas Requirements Operational Service Check Procedure Prior to February 11 Control Panel Microprocessor As of February 11 With circuit breaker Reversing Relay Panel With fuses Gas Burner Assembly HSI Module Gas Models Drive Motor Blower Motor and Impeller Taperlock Trantorque Drive Shaft Assembly Idler Shaft Assembly Transtorque Taperlock Main Door Switch Basket Tumbler Sail Switch Gas Models Only Hi-Limit Gas Models Only Automatic Reset Thermostat Lint Screen Lint Drawer Switch Servicing Computer Controls To Replace Keyboard Label Assembly HSI Ignitor Flame Sensor Probe Ignition ControlsTo Remove Flame Sensor Probe To Replace Main Burner Orifices To Test and Adjust Gas Water Column PressureTo Replace Gas Valve See burner illustration on To Convert Natural Gas to L.P. Gas To Replace Burner Tubes Discontinue power to the dryer To Replace HSI Module To Adjust Sail Switch Sail Switch Assembly Gas Models OnlyTo Replace Sail Switch To Install New Main Door Glass as of October 24 To Replace Main Door SwitchTo Replace Main Door Assembly Front Panel and Main Door Assemblies As of October 24 Prior to October 24 To Replace Main Door Hinge Block To Install new Main Door Glass prior of October 24To Replace Front Panel Pulleys To Replace Drive Shaft Pulley To Replace Drive Motor PulleyPage Tumbler Wheel Replacement on IdlerAssembly taper lock models Tumbler Wheel Replacement on IdlerAssembly trantorque models To Replace Blower Shaft Pulley Basket Assembly To Replace Blower Motor Pulley To Replace Idler Shaft Pillow Block Bearing To Replace Drive Assembly Pillow Block BearingBelt Adjustment Motor to Drive Axle To Replace Impeller Motor Fan Shaft Drive To Replace Drive Motor V-BeltsMotors To Replace Blower Motor V-belts To Replace Front Thruster Wheels Rear Access Impeller To Replace Lint Screen Lint Screen AssemblyTo Replace Lint Door Switch Dryer will not start, but computer display indictors are on No display on computerComputer will not accept key pad entries Drive motor runs, burner is on, but basket will not turn Overload for impeller fan motor is tripping Burner hi-limit safety thermostat is trippingThermal overload for drive motor is tripping There is excessive vibration coming from the basket Phase 6 OPL System Diagnostics Page E.D. Display Indicators E.D Display Indicator Number AIR AIR JET Output L.E.D. Indicator Optional FAN Blower Output L.E.D. Indicator Fuse Main Fuse Input L.E.D. Indicator Flame bURNER Control Fail Input L.E.D. Indicator E.D. Codes BURNER Control Fail BURNER Safety FailDRUM Safety Fail BURNER Flame Fail Computer Logic and Wiring Diagram No Display Condition Drive motor reverses but does not forward, blower motor runs Blower motor does not operate, drive motor runs Lint Door Condition Main Door Condition Microprocessor Which Must be Reset Manually Technical Information For example Data Label HOW to USE a Manometer AD-95/ML-95 Tool List ADC450188 1- 01/14/99-25