Input, Connecting the 40kW UPS | APC 10-40KW 400V UPS manual

External Connection

NOTICE!

Install gland plate in bottom of unit

4.1.2 Connecting the 40kW UPS

CAUTION!

At a switch mode load of 100% the neutral must be rated for 200% output phase current.

CAUTION!

This UPS unit is an EN 50091-2 product and may cause radio interference in a domestic environment. Take preventive measures if necessary.

Optional

Input

Output

Parallel Controller

Please refer to 8.5

System Integration interface

Communication Interface

Relay Board (Optional)

	990-4050

Installation Guide APC Silcon 10-40kW 400V UPS	15

Image 15

APC 10-40KW 400V UPS manual Input, Connecting the 40kW UPS

Contents

10-40kW 400V UPS Installation Guide Installation Guide APC Silcon 10-40kW 400V UPS Safety Symbols used in this manualThank You Contents Appendix System SpecificationsWarranty 10.0 How to Contact APC Tools IntroductionIntroduction Tools and Equipment Unpacking Unpacking Please Recycle 1xBP 2xBP 3xBP InstallationInstallation Requirements on Site Cabinets 1 600mm UPS Cabinet with 1xBP I or Isolation Transformer Footprint 4 600mm Cabinet for 40kW UPS without Batteries 3 1000mm Cabinet for 10-20kW UPS with 3xBP 5 1000mm Cabinet for 40kW UPS with 2xBP External Connection Connecting the UPSConnecting the 10-20kW UPS External Connection Battery Cable OutputFuses 10kW 20kW Input Connecting the 40kW UPS 40KW Mm2 Output CableFuses Mm2 System Integration Interface Connections Parallel Board Parallel BoardTerminal Blocks X003/X004 Anxiliary Contacts X005 Output Relays External Connection External Control Cables Power Cables Communication Interface Board X50 and a serial port Connecting of APC Silcon Tripel Chassis 2.1Monitoring Port Safety WarningsAPC Silcon Triple Chassis Product Description If the LED is… Then the Silcon Triple Chassis… 2.4Optional Power InputInstalling Management Peripherals 2.3LEDs 3.3Daisy-chaining the APC Silcon Triple Chassis 3.2Installing Management Peripheral Cards3.1Order of Management Peripheral Cards Management Priority Position Peripheral Card Management Peripheral Draw mA Troubleshooting Problem Possible Cause Solution5.1If Problems Persist External Connection External Connection 6.2Power, Physical, and Environmental Specifications PhysicalEnvironmental Important Safety Instructions APC Silcon Battery Cabinets Preparing Batteries External Connection External Connection External Connection Final Checks APC Silcon Battery Cabinets 5.1Installation of Batteries Diagram UPS with Battery CabinetSilcon Battery Breaker Box/Fuse-box 20 kW Battery Breaker BoxAmpere Connection Max Dimensions Weight Rating Cable Short Circuit Current kA 10 kW Battery Battery Breaker Box Connection Diagram Fuse-box Fuse-box Connection Diagram External Connection Parameters Parameter Setting CommentsProgramming Parameters Programming Parameters Programming Keys Programming Example Switch to Bypass Operation System Configuration System Configuration Parameters password protected Programming Example Change Charge Voltage to Change parameters by pressing Programming Parameters for Advanced Parallel Operation Description of Settings Programming example Battery Monitor Options/Accessories Options/AccessoriesService Bypass Panel for Single Operation 10 x 0.75mm2 max mm2 Options/Accessories Display shows Operating The External Service Bypass Switch Lamp indication On Servive Bypass Panel 3.1Switching from External Bypass to Normal UPS Operation Service Bypass Panel for Parallel Redundant Operation Two Parallel Systems with Service Bypass Panel Options/Accessories H002a Action Options/Accessories Lamp indication On Service Bypass Panel ActionDisplay shows Following can be carried out on any UPS Isolating One UPS for Service/Maintenance Switching Back to Normal Parallel/Redundant Operation Intersystem Synchronization Unit Intersystem Synchronization Unit System ISU SystemIntersystem Synchronization Unit ISU Relays Relay Board Relay Board/Relay Functions Relay Number Message Alarm-trigging Events See .2 in this guide for System configuration Footprint 600mm Weight Equalizer Footprint 1000mm Cabinet Remote Display Extension of Remote Display Communication DistanceStandard Short-haul RS232 Modem Async Pin Connections for cable from host to ME800A-R2 Host 1.1Connections Without ConverterHost DTE Remote Display DTE 1.2Connections With Converter Remote Display Cables 2.2Remote Display Power Supply Remote Display Use 3.2Communication FaultRemote Display Setting 3.6Alarms Isolation Transformer Height mm Width mm Depth mm Weight kg Input Fuses Input Cable Cable mm2 Output Temp FM a Connecting Isolation TransformerCable Signal Isolation External External PE Options/Accessories Options/Accessories Options/Accessories Options/Accessories Options/Accessories Options/Accessories Back-up Time / Dimensions / Weigh System SpecificationsSystem Specifications Technical Data Warranty WarrantyAPC Silcon Series Limited Factory Warranty Installation Planning Data AppendixAppendix Appendix APC Denmark How to Contact APCHow to Contact APC APC Corporate