Connecting of APC Silcon Tripel Chassis | APC 10-40KW 400V UPS

External Connection

4.5Connecting of APC Silcon Tripel Chassis

The enclosed Triple Chassis must be connected to the serial port on the Communication Interface Board, and to the 24V supply (cables included). Terminal locations shown below.

23.62 inch/600mm Cabinet

Serial ports

Front view of UPS Cabinet (doors open)	X50 is a 24V supply for Triple Chassis.
	X50 is a 24V supply for Triple Chassis.
	Only to be used for this purpose.
	Not suitable for telephone equipment.
	Triple Chassis must be connected to both
	X50 and a serial port.

APC Silcon Triple Chassis

For more information please refer to the following section.

990-4050

Installation Guide APC Silcon 10-40kW 400V UPS

23

Image 23

APC 10-40KW 400V UPS manual Connecting of APC Silcon Tripel Chassis, X50 and a serial port

Contents

10-40kW 400V UPS Installation Guide Thank You Installation Guide APC Silcon 10-40kW 400V UPSSafety Symbols used in this manual Contents Appendix System SpecificationsWarranty 10.0 How to Contact APC Tools IntroductionIntroduction Tools and Equipment Unpacking Unpacking Please Recycle 1xBP 2xBP 3xBP InstallationInstallation Requirements on Site Cabinets 1 600mm UPS Cabinet with 1xBP I or Isolation Transformer Footprint 4 600mm Cabinet for 40kW UPS without Batteries 3 1000mm Cabinet for 10-20kW UPS with 3xBP 5 1000mm Cabinet for 40kW UPS with 2xBP External Connection Connecting the UPSConnecting the 10-20kW UPS External Connection Fuses 10kW 20kW Battery CableOutput Input Connecting the 40kW UPS 40KW Mm2 Output CableFuses Mm2 System Integration Interface Connections Parallel Board Parallel BoardTerminal Blocks X003/X004 Anxiliary Contacts X005 Output Relays External Connection External Control Cables Power Cables Communication Interface Board X50 and a serial port Connecting of APC Silcon Tripel Chassis 2.1Monitoring Port Safety WarningsAPC Silcon Triple Chassis Product Description If the LED is… Then the Silcon Triple Chassis… 2.4Optional Power InputInstalling Management Peripherals 2.3LEDs 3.3Daisy-chaining the APC Silcon Triple Chassis 3.2Installing Management Peripheral Cards3.1Order of Management Peripheral Cards Management Priority Position Peripheral Card Management Peripheral Draw mA 5.1If Problems Persist TroubleshootingProblem Possible Cause Solution External Connection External Connection Environmental 6.2Power, Physical, and Environmental SpecificationsPhysical Important Safety Instructions APC Silcon Battery Cabinets Preparing Batteries External Connection External Connection External Connection Final Checks APC Silcon Battery Cabinets Silcon 5.1Installation of BatteriesDiagram UPS with Battery Cabinet Battery Breaker Box/Fuse-box 20 kW Battery Breaker BoxAmpere Connection Max Dimensions Weight Rating Cable Short Circuit Current kA 10 kW Battery Battery Breaker Box Connection Diagram Fuse-box Fuse-box Connection Diagram External Connection Parameters Parameter Setting CommentsProgramming Parameters Programming Parameters Programming Keys Programming Example Switch to Bypass Operation System Configuration System Configuration Parameters password protected Programming Example Change Charge Voltage to Change parameters by pressing Programming Parameters for Advanced Parallel Operation Description of Settings Programming example Battery Monitor Service Bypass Panel for Single Operation Options/AccessoriesOptions/Accessories 10 x 0.75mm2 max mm2 Options/Accessories Display shows Operating The External Service Bypass Switch Lamp indication On Servive Bypass Panel 3.1Switching from External Bypass to Normal UPS Operation Service Bypass Panel for Parallel Redundant Operation Two Parallel Systems with Service Bypass Panel Options/Accessories H002a Action Options/Accessories Display shows Lamp indication On Service Bypass PanelAction Following can be carried out on any UPS Isolating One UPS for Service/Maintenance Switching Back to Normal Parallel/Redundant Operation Intersystem Synchronization Unit ISU Intersystem Synchronization UnitIntersystem Synchronization Unit System ISU System Relays Relay Board Relay Board/Relay Functions Relay Number Message Alarm-trigging Events See .2 in this guide for System configuration Footprint 600mm Weight Equalizer Footprint 1000mm Cabinet Standard Short-haul RS232 Modem Async Remote DisplayExtension of Remote Display Communication Distance Pin Connections for cable from host to ME800A-R2 Host 1.1Connections Without ConverterHost DTE Remote Display DTE 1.2Connections With Converter Remote Display Cables 2.2Remote Display Power Supply Remote Display Use 3.2Communication FaultRemote Display Setting 3.6Alarms Isolation Transformer Height mm Width mm Depth mm Weight kg Input Fuses Input Cable Cable mm2 Output Temp FM a Connecting Isolation TransformerCable Signal Isolation External External PE Options/Accessories Options/Accessories Options/Accessories Options/Accessories Options/Accessories Options/Accessories Back-up Time / Dimensions / Weigh System SpecificationsSystem Specifications Technical Data APC Silcon Series Limited Factory Warranty WarrantyWarranty Appendix Installation Planning DataAppendix Appendix APC Denmark How to Contact APCHow to Contact APC APC Corporate