STEEL UM7id OK.FH11 Mon Feb 22 13:46:32 2010 Página 12
C M Y CM MY CY CMY K
Notes:
1.The filter holder should always be
placed in the machine so that it
remains warm. Closed position.
2.Only UNO model. If the coffee does
not come out very hot, press steam
switch
3
for 10 seconds. This will
raise the temperature of the machine
3.Place the cups on the cup warmer
9
. The right temperature (optimum
40ºC/105ºF) will improve the
espresso. (see picture 6)
4 .Coffee will continue to drip from the
spouts for a moment after the coffee
swich is turned off.
!
THERMOMETER
The thermometer will mark you the
machine temperature. It has to be in
between 80ºC/180ºF and 110ºC/230ºF
for coffee and above 100ºC/212ºF
degrees for steam
!
Important: Tamped
The best espresso result are
obtained when the ground coffee is
firmly tamped.
5-. Programming the amount
of coffee (TRONIC)
Electronic push-button control functions.
S: small coffee
L: large coffee
XL: non-stop coffee (push button again
to stop flow)
Programming the amount of coffee
With the machine on, push the XL
programming button for 5 or 6 seconds
until the LED flashes.
Push the S small coffee button. The
LED will light up, at the same time the
XL programming LED stops flashing.
Let the coffee flow.
Once you have the desired amount,
push the S again. The machine is now
programmed.
To programme large coffee L, repeat
the operation.
To personalise the amount of coffee
(non-stop), push the XL button. Once
you have the desired amount, push the
button again to stop the flow of coffee.
6-. Preparation of cappuccino
UNO Mobile filterholder
1-.Press general switch
1
. Pilots 13
and
6
will come on.
2.-When pilot 6 goes out, press steam
switch
3
. Pilot
6
will come on.
3.-Wait for light
6
to go out. This
indicates that the coffee machine has
reached its ideal
temperature.reached the ideal
temperature.
4-.Turn the hot water/steam knob
4
to
open and allow the first drops of water
to come out. In a few moments, only
steam will come out.
5-.Put the tube
5
into the milk to heat
it so that the milk covers exactly half
the absorption hole (never totally
cover it). Do this for the whole
process. (see picture 7)
6.-Liquid is absorbed through the hole
and cream forms automatically.
The recipient should be lowered
gradually while the milk emulsifies.
7.-Turn the water/steam knob
4
to
closed - and turn off the steam switch
3
.
UNO Fixed filterholder
1.-Press general switch
1
. Pilots 13
and
6
will come out.
2.-When pilot
6
goes out, press switch
3
and pilot
6
will come on
simultaneously and the pump will be
pressed at short intervals.
3.-Wait for approximately 15 and then
open side knob
4
and let the first
drops of water run out. After a
moment only steam will come out.
Points 5, 6 and 7 are the same as in
the previous section.
DUO VAPOR / TRIO
1-.Turn on the main switch
1
.
On TRIO Model turn on the switch
18
, wait for a 1,5 minues approx. If
the machine was already turned on
(and the TRIO switch
18
- was
already on), pass to step nº 2.
2-.Press switch
3
.The pilot light will turn
on.
3-.You will get steam instantly.
4-.Put the tube
5
into the milk to heat
it so that the milk covers exactly half
the absorption hole (never totally
cover it). Do this for the whole
process. (see picture 7)
5-.Liquid is absorbed through the hole
and cream forms automatically.
The recipient should be lowered
gradually while the milk emulsifies.
6-.Turn off the switch
3
.
If you want a creamy cappuccino, use
cold, fresh, whole milk.
For obtaining micro-foam, you should
maintain the absortion hole in the
same position.
ascasoascaso
ENGLISH
ENGLISH
20 21
Picture 5
Picture 7
Picture 6