Starting up the Service Mode | Barco 9200 instruction

Service Mode

10 SERVICE MODE

Starting up the Service Mode

Push the control stick forward or backward to highlight Service and then press ENTER.

Some items in the Service mode are password protected (when the password function is active). Enter your password to continue. All other password protected items are now available if you stay in the adjustment mode.

The service menu is built-up in two parts which are connected together with the 'more' item.

If the disered item is not in the list of the displayed menu, select more with the control stick and push ENTER to display the other items in the service menu.

ENTER continues to the Service mode selection menu. EXIT returns to operational mode.

ADJUSTMENT MODE

Select a path from below :

GUIDED

RANDOM ACCESS

INSTALLATION

SERVICE

Source 01

Select with	SERVICE
then
<EXIT> to	IDENTIFICATION
	CHANGE PASSWORD
	CHANGE LANGUAGE
	CHANGE PROJ. ADDRESS
	CHANGE BAUDRATE PC
	RESET LAMP RUNTIME
	LAMP RUNTINE HISTORY
	LAMP POWER : 1500W
	MORE...

Select with or then <ENTER> <EXIT> to return.

SERVICE

PANEL ADJUSTMENTS

PRESET INPUT BALANCE

60Hz TRACKING

I2C DIAGNOSIS

MORE...

Select with or then <ENTER> <EXIT> to return.

SERVICE

IDENTIFICATION

CHANGE PASSWORD CHANGE LANGUAGE CHANGE PROJ. ADDRESS CHANGE BAUDRATE PC RESET LAMP RUNTIME LAMP RUNTINE HISTORY DIMMING

MORE...

Select with	or
then <ENTER>
<EXIT> to	return.

SERVICE

BARCO

GRAPHICS 9200

Proj. address : 001 Soft. version : 3.0 Config : front/

ceiling

Baudrate PC : 9600

text : ON

Serial no.: 1010200

Run time : 100 h

Select with or

then <ENTER>

<EXIT> to return.

CHANGE PASSWORD

Enter new password

0000

Select with or then <ENTER> <EXIT> to return.

CHANGE LANGUAGE

ENGLISH

FRANCAIS

Select with or then <ENTER> <EXIT> to return.

PANEL ADJUSTMENTS

PRESET INPUT BALANCE

60Hz TRACKING

I2C DIAGNOSIS

MORE...

Select with	or
then <ENTER>
<EXIT> to	return.

CHANGE PROJ. ADDRESS

Enter new address

001

Select with or Reprogram with or

or numeric keys

<ENTER> to confirm

<EXIT> to return

LAMP RUNTIME HISTORY

Serial No Runtime

-----------------------------------------------------

> 0111121	600	h
0110031	750	h
0110010	745	h

-----------------------------------------------------

<EXIT> to return

CHANGE BAUDRATE PC

9600

4800

2400

1200

600

300

150

75

Select with or

<ENTER> to accept

<EXIT> to return.

RESET LAMP RUN TIME

Enter the

serial number

of the new lamp

0000000

Select with or Reprogram with or

or numeric keys

<ENTER> to confirm

<EXIT> to return

5975947 BARCOGRAPHICS 9200 120297		11-1

Image 41

Barco owner manual Starting up the Service Mode, Barcographics 9200 11-1

Contents

Graphics Page Date Rev Art. No 030798 R5975947 Barco Projection Systems Federal communication commission FCC statement Table of Contents 10-2 10-110-4 11-1 Unpacking Unpacking and DimensionsProjector dimensions Battery installation in the RCU Installation Guidelines How to install a projection lens? Where to install the projector?RGB Analog with Standard Sync Sync on Green or RGB Analog with TRI-LEVEL Sync Sync on Green or Front Panel Terminology Control RC operating indication lights up when a button on Remote controlControl disc Key on RCU or + and keys cursor Local keypad Installation Actual selected configuration will be highlightedConfiguration Front/table, front/ceiling, rear/table and rear/ceiling Installation Set Up Switching on Power mains cord connectionConnections Fuses Switching off Switching to stand-byLamp Run Time Input connections 269,2VIDEO,1387 Video/S-video input module RGB Analog Input Module 2032117B-Y S9,2,1387 Component Input Module RGB3S/RG3sB Input Module See Change Baudrate PC in chapter Service mode Set up of the baud rate for communication with a computer Connecting an IR Remote Receiver 800 to the projector Connecting a Rcvds 05 to the projectorConnecting a VS05 to the projector Controlling How to Use the RCU?Projector Address Point the front of the RCU to the reflective screen surface Picture Controls with Direct Access How to Display a Projector Address?How to Program an Address into the RCU? Adjustment Mode Start UP of the Adjustment Mode Start up of the Adjustment Mode File Service Random Access Adjustment ModeStarting up the Random Access Adjustment Mode Load File File ServiceEdit File Edit file adaptation menu will be displayed How to find the correct values for the displayed item? Example for clamp position trailing Copy RenameRename Copy File Options Picture TuningDelete Sync slow/fast Color TemperatureStill Video Comparison with the green color value Geometry GammaShift Size Blanking Side KeystoneSide Keystone Blanking Options Input Slots Starting up the Installation Mode Convergence Convergence RED on Green Internal Patterns Configuration Starting up the Service Mode Service ModeService Barcographics 9200 11-1 Identification Identification How to enable or disable the password function ? Change Password Change Language How to change the password ?Change Projector Address Change Baudrate PC Lamp Power Reset Lamp RuntimeLamp Run Time History Barcographics 9200 11-5 Preset Input Balance Panel AdjustmentsHz Tracking I2C diagnosis Standard Source SET UP Files 640 X 74,996 68,846 57,280 832 918 870 KHz MHz XGA72 1024 768 71,955 58,140 80,000 1376 808832 X 74,550 49,722 57,280 1152 667 624 640 X 55,370 24,370 21,060 864 440 400 Lenses Focusing the lensLens Cleaning Procedure Lenses Projector with a 800 peripheral connected Projector without any 800 peripheral connected Source numbers 81 13873525&8-6285&6&725