Using build-in test pattern | BenQ MW767, MX766, MX822ST instruction

Using build-in test pattern

You can adjust the image shape and focus status by observing the input signal content, or using the test pattern build-in OSD manual from OSD or remote control for better observe the shape changed.

Open the OSD menu and go to the SYSTEM SETUP: Advanced > Test Pattern > On. Press MODE/ENTER. The Test Pattern displays.

Fine-tuning the image size and clarity

1.Adjust the projected image to the size that you need using the zoom slide lever. (MX766/MW767)

MX766/MW767

2.Then sharpen the image by using the focus ring/focus slide lever.

MX766/MW767 MW822ST

Operation 31

Image 31

BenQ MW767, MX766, MX822ST user manual Using build-in test pattern, Fine-tuning the image size and clarity

Contents

MX766/MW767/MX822ST Digital Projector Table of contents Projector lens during operation Important safety instructionsSafety Instructions Do not look straight at Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector features Shipping contents Optional accessories Front/upper side Projector exterior view MX822ST Rear/lower side Keystone/Arrow keys / Up Down Volume /Arrow keys / Left, / RightPower/POWER indicator light Controls and functions Mounting the projector Test Remote controlVolume /Arrow keys / Left Right Zoom + MIC/VOL + Operating the laser pointerHdmi Auto Replacing the remote control battery Front Table Set Rear Ceiling in the System Setup BasicPositioning your projector Choosing a location Obtaining a preferred projected image size Max length Inch Max. zoom Min. zoom Projection dimensionsMX766 MW767 MX822ST Connection Operation System Minimum Hardware Requirements Connecting a computer Connecting a computer or monitor To connect the projector to a monitor Connecting a monitor Connecting an Hdmi source device Connecting Video source devicesTo connect the projector to an Hdmi source device To connect the projector to a Component Video source device Connecting a Component Video source device To connect the projector to an S-Video/Video source device Connecting an S-Video/composite source device Connecting with document camera Starting up the projector Operation Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Using build-in test pattern MODE/ENTER . The Keystone correction Correcting keystone Language and press Enter to Using the menus If you forget the password Using a security cable lockUtilizing the password function Setting a password Changing the password Entering the password recall procedure Disabling the password function Switching input signalChanging Color Space Magnifying and searching for details About the aspect ratio Selecting the aspect ratio Optimizing the image Selecting a picture mode Fine-tuning the image quality in user modes Using Wall Color Selecting a Color Temperature Adjusting TintAdjusting Sharpness Adjusting Brilliant Color Press MODE/ENTER and the 3D Color Management page displays To cancel the timer, perform the following steps Setting the presentation timer Hiding the image Remote paging operationsFreezing the image Muting the sound Adjusting the soundAdjusting the sound level Operating in a high altitude environment Adjusting the microphone’s sound level Turning off the Power on/off ring tonePersonalizing the projector menu display Until the System Setup Advanced menu is highlighted Select the lamp saver mode Use Teaching Template If you are in a Dhcp environment Configuring the Wired LAN SettingsConfiguring the Wireless LAN Settings Controlling the projector through a LAN environment Controlling the projector remotely through a web browser Through Q Presenter on page 59 for details Page Page Iii Page Page Page Page Displaying image through Q Presenter Iii Iii Vii Using the Projection Login Code Using the Web Control Lock Preparation Using the broadcassting functionPresenting From a USB Reader Image File Types Press Controlling USB Reader Press Settings Remote Desktop Control through Q Presenter Enter Shutting down the projector PointDraw Pen Menu system Menu operation System Setup Basic CC1/CC2/CC3/CC4 Dhcp Display menu Description of each menu 3D Sync Invert 3D Mode Picture menu Picture mode on page 39 for details Picture menu Source menu System Setup Basic menu Blank Timer Direct Power OnSignal Power On Auto Power Off See PointDraw Pen on page 70 for details System Setup Advanced menu Caption Version Closed Caption Enable Microphone Wired LANWireless LAN Network Source System Setup Advanced menu Information menuPicture Mode Resolution Care of the projector Maintenance Getting to know the lamp hour Setting Lamp Mode eco function as Economic or SmartEco modeSetting Auto Power Off Lamp informationPage Status Message Timing of replacing the lamp Replacing the lamp Page Tighten the screws that secure Lamp Resetting the lamp timer Light Status & Description IndicatorsLamp events Thermal Sensor 2 short error Thermal Sensor 2 open errorThermal IC #2 I2C Connection error Troubleshooting Specifications Dimensions Ceiling mount screw M4 Max L = 25 mm Min L = 20 mm Unit mm Ceiling mount installation Minimum installation requirements Wall mount installation Minimum Ceiling Height mm = f + H + b + 60 + 262.2+ c Supported timing for PC input Timing chart Supported timing for Hdmi input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinput Video timing Supported 3D signal for Hdmi Hdcp inputPC timing Supported 3D signal for D-SUB input Supported 3D signal for Video and S-Video input Copyright Warranty and Copyright informationLimited warranty Patents