Fault | Possible cause | Action |
Control lights do not lightA fuse has blown. up.
Power failure.
Appliance is in energy7saving mode.
This is not a fault.
Program does not start. Start/Pause button not pressed. Start/Pause indicator
light flashes.
Program does not start. Door not closed properly.
"Check Door !" indicated in the display field.
Replace the fuse of the individual circuit.
Call | Customer | Service | if this fault recurs. | ||
|
|
|
|
|
|
An | interrupted | program | will | be resumed when power | |
is restored. If the laundry | is to be removed during a | ||||
power failure,call Customer | Service | ||||
(refertoPage 35). |
|
|
| ||
Press theSelect button; energy7saving mode is | |||||
terminated. |
|
|
|
| |
|
| ||||
Press theStart/Pause button. | |||||
Check whether laundry is trapped in door.
Close the door (a click should be heard). Program continues.
"Press | start" | is indicated | End time selected but still not activated by pressingPress theStart/Pause button. | |||
in the | display | field. | the Start/Pause" button. | |||
|
|
|
|
|
|
|
Program does not start. "Real Time delay" is indicated in the display field.
Clock cannot be set.
End time selected and activated. | None. Appliance starts automatically. |
Program has already started; when a program hasWait until program ends. started, the clock cannot be set.
"Set | clock:" text | remains | The setting has | switched | from hours to minutes; Noneboth. | |||
in the display field even | selection points | have the | same text. | |||||
though theMenu | button |
|
|
|
|
| ||
has | been pressed. |
|
|
|
|
|
| |
No time displayed.
End time cannot be selected.
Time | not | set. |
| Set | time; | see | Page | 27. |
|
|
|
|
|
|
|
|
|
Time | not | set. |
| Set | time; | see | Page | 27. |
|
|
|
|
|
|
|
|
|
Program has already started; when a program hasBefore starting the program, select and start the started, the end time can no longer be selected.desired end time; see Page24.
Spin speed cannot be selected.
Spinning is already in progress; during spin cycle Selthect speed before spinning. speed cannot be changed.
Program | selector | is setDrainto | ; spin cycle is not If required, select another program. | ||
possible | with this | program. |
|
|
|
|
|
|
|
|
|
Child lock cannot be |
| The program has already started. |
selected. |
|
|
|
|
|
Detergent residue in the Detergent was damp or lumpy. detergent dispenser.
Child lock can be selected in pause mode.
Clean and dry the detergent dispenser; see Page 30.
Use the cap of the detergent bottle to measure liquid detergents.
Water does not enter theWater tap not turned on. |
|
|
| Turn | on | water | tap. | |||||||||||
machine or | detergent | is |
|
|
|
|
|
|
|
| Program | continues. | ||||||
not washed | away. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| Supply | hose kinked | or pinched. |
|
| Eliminate | the | cause. | |||||||||
"Water | tap |
|
|
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
tapclosed?"" |
|
| Strainers in | supply | hose | clogged. |
|
| Clean | the water | inlet strainers; see Page 30. | |||||||
indicated in the display |
|
|
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
| Water | pressure | too | low. |
|
|
| Eliminate | the | cause. | |||||||
field. |
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Water | cannot be seen |
| in This | is | not | a | fault. |
|
|
|
|
|
|
|
|
| ||
drum. |
|
|
|
| The | water | level is | below | the visible | part of the drum. |
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
33
