Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 6H122-08 manual General Configuration Screen

Models: 6H122-08

1 170

Download 170 pages 13.93 Kb

Page 84

5.15GENERAL CONFIGURATION SCREEN

Chapter 5: Local Management

5.15GENERAL CONFIGURATION SCREEN

The General Conﬁguration screen, Figure 5-18, allows the user to set the system date and time, IP address and subnet mask, the default gateway, the TFTP Gateway IP address, the Operational Mode, the Management Mode, and the COM port conﬁguration. The General Conﬁguration screen also allows the user to Clear NVRAM, and enable or disable IP Fragmentation.

Access the General Conﬁguration screen from the Module Conﬁguration Menu screen by using the arrow keys to highlight the GENERAL CONFIGURATION menu item and pressing ENTER. The General Conﬁguration screen, Figure 5-18, displays.

Event Message Line

		6H122-08 LOCAL MANAGEMENT
			General Configuration
Module Type: 6H122-08					Firmware Revision:	XX.XX.XX
Slot Number: X					BOOTPROM Revision: XX.XX.XX
MAC Address:		00-00-ID-00-00-00			Module Date:	10/11/97
IP Address:					Module Time:	14:23:00
IP Address:		0.0.0.0			Module Time:	14:23:00
Subnet Mask:	255.255.0.0				Screen Refresh Time:	30 sec.
Default Gateway:		NONE DEFINED			Screen Lockout Time:	15 min.
TFTP Gateway IP Addr:	0.0.0.0				Module Uptime XX D XX H XX M
Operational Mode: [802.1D SWITCHING]					Management Mode: [DISTRIBUTED]
Com: [ENABLED]	Application:		[LM]
Clear NVRAM [NO]	IP Fragmentation [ENABLED]
SAVE			EXIT			RETURN

2159_16

Figure 5-18 General Conﬁguration Screen

The following brieﬂy explains each General Conﬁguration screen ﬁeld:

MAC Address (Read-Only)

Displays the base physical address of the module.

5-40	6H122-08 User’s Guide

Image 84

Cabletron Systems 6H122-08 manual General Configuration Screen

Contents

6H122-08 SmartSwitch 6000 Interface Module User’s Guide 6H122-08 RESET1X 2X 3X 4X 5X 6X CPU 100 MbsPage FCC NOTICE 6H122-08 User’s GuideINDUSTRY CANADA NOTICE VCCI NOTICECABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT 6H122-08 User’s GuideEXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY CABLETRON SOFTWARE PROGRAM LICENSEUNITED STATES GOVERNMENT RESTRICTED RIGHTS 6H122-08 User’s GuideDECLARATION OF CONFORMITY 6H122-08 User’s GuideCONTENTS INSTALLATIONCHAPTER INTRODUCTIONContents TROUBLESHOOTINGCHAPTER CHAPTERContents 6H122-08 User’s GuideContents SPECIFICATIONSSPECIFICATIONS OPTIONAL INSTALLATIONS AND1.1 USING THIS GUIDE CHAPTER INTRODUCTION1.2 STRUCTURE OF THIS GUIDE Chapter 1 Introduction Reset Button COM Port System LED Port Status LEDs Network Ports RESETStructure of This Guide 6H122-08 User’s Guide1.3 6H122-08 OVERVIEW 1.3.1 Auto-Negotiation1.3.2 Connectivity 1.3.3 Full Duplex Switched Ethernet FDSE 1.3.5 Switching Options1.3.4 Management 1.3.6 Standards Compatibility1.3.7 LANVIEW Diagnostic LEDs 1.3.8 Year 2000 Compliant1.3.9 Runtime IP Address Discovery 1.4 LOCAL MANAGEMENT FEATURES 1.4.1 Distributed Chassis Management1.4.2 Remote Monitoring RMON 1.4.3 Broadcast Suppression1.4.4 Port Redirect Function 1.4.5 SmartTrunk1.5 OPTIONAL FEATURES 1.4.6 Additional Local Management Functions1.6 DOCUMENT CONVENTIONS The following conventions are used throughout this documentChapter 1 Introduction 1-101.7 GETTING HELP 1.8 RELATED MANUALS The following manuals may help the user to setup and manage the6H122-08 Cabletron Systems Cabling GuideCHAPTER NETWORK REQUIREMENTS 2.1 SmartTrunk2.2 10BASE-T NETWORK 2.3 100BASE-TX NETWORK 2.4 100BASE-FX FIBER OPTIC NETWORKMultimode Mode Fiber Optic Cable Length Single Mode Fiber Cable LengthsCHAPTER INSTALLATION 3.1 REQUIRED TOOLS3.2 UNPACKING THE 6H122-08 3.3 INSTALLING OPTIONS 3.4 INSTALLING THE 6H122-08 INTO THE 6C105 CHASSISor components To prevent damaging the backplane connectors in the following engages the backplane connectorsstep, take care that the module slides in straight and properly Chapter 3 Installation Figure 3-1 Installing an Interface ModuleRESET 6H122-08 User’s Guide3.5 CONNECTING TO THE NETWORK 3.5.1 Connecting Twisted Pair Cables to Ports 1 ThroughRX Receive LED Column Figure 3-2 6H122-08 Twisted Pair Connection3.5.2 Connecting a Twisted Pair Segment to the FE-100TX Figure 3-3 Cable Pinouts - RJ45 Crossover CableFigure 3-4 FE-100TX Crossover Switch 100 FE-100TX3.5.3 Connecting a Fiber Optic Segment to the FE-100FX and FE-100F3 Fiber Optic Network ConnectionThe port RX LED ﬂashes green and amber during bootup Figure 3-5 FE-100FX and FE-100F3 Port3.6 COMPLETING THE INSTALLATION Completing the Installation6H122-08 User’s Guide 3-11Chapter 3 Installation 3-126H122-08 User’s Guide CHAPTER TROUBLESHOOTING 4.1 USING LANVIEWChapter 4 Troubleshooting 6H122-08 RESET6H122-08 User’s Guide Figure 4-1 LANVIEW LEDsUsing LANVIEW 6H122-08 User’s GuideTable 4-1 LANVIEW LEDs Color4.2 FE-100TX LED Table 4-1 LANVIEW LEDs ContinuedTable 4-2 Port 1-6 10/100 LED Indications 100 LED Receive RX LEDFE-100TX LED 6H122-08 User’s Guide4.3 TROUBLESHOOTING CHECKLIST Chapter 4 TroubleshootingTable 4-4 Troubleshooting Checklist Problem4.4 USING THE RESET BUTTON 6H122-08Chapter 4 Troubleshooting 6H122-08 User’s GuideCHAPTER LOCAL MANAGEMENT 5.1 OVERVIEW5.2 LOCAL MANAGEMENT KEYBOARD CONVENTIONS Chapter 5 Local Management6H122-08 User’s Guide Table 5-1 Keyboard Conventions5.3 MANAGEMENT TERMINAL SETUP 5.3.1 Console Cable ConnectionUTP Cable with RJ45 Connectors RJ45-to-DB9 PC Adapter to PC RESETRESET Chapter 5 Local Management5.3.2 Connecting an Uninterruptible Power Supply Figure 5-2 Uninterruptible Power Supply UPS UTP Cable with RJ45 Connectors RJ45-to-DB9 PC Adapter DB9 Port6H122-08 RESET CPU 100 Mbs RESET5.3.3 Management Terminal Setup Parameters Management Terminal SetupTable 5-2 VT Terminal Setup Display Setup MenuTelnet Connections 5.4 ACCESSING LOCAL MANAGEMENT Figure 5-3 The Local Management Chassis/Module Password Screen5.4.1 Navigating Local Management Screens Accessing Local Management Figure 5-4 802.1D Switching Mode, LM Screen HierarchyFigure 5-5 802.1Q Switching Mode, LM Screen Hierarchy 6H122-08 User’s Guide5.4.2 Selecting Local Management Menu Screen Items 5.4.3 Exiting Local Management Screens5. Press ENTER. The Password screen displays and the session ends 5.5 THE MAIN MENU SCREEN CHASSIS5.6 CHASSIS MENU SCREEN MODULES5.7 CHASSIS CONFIGURATION SCREEN CHASSIS CONFIGURATION802.1Q VLAN CONFIGURATION SNMP COMMUNITY NAMESThe following brieﬂy explains each Chassis Conﬁguration screen ﬁeld Section Subnet Mask ModiﬁableChassis Date Modiﬁable Chassis Time Modiﬁable5.7.1 Setting the IP Address 5.7.2 Setting the Subnet Mask 5.7.3 Setting the Chassis Date 5.7.4 Setting the Chassis Time5.7.6 Setting the Screen Lockout Time 5.7.5 Entering a New Screen Refresh Time5.7.7 Setting the Operational Mode 5.8 SNMP COMMUNITY NAMES SCREEN The following explains each SNMP Community Names screen ﬁeld 5.8.1 Establishing Community Names 5.9 SNMP TRAPS SCREEN 5.9.1 Conﬁguring the Trap Table Enable Traps Toggle5.10 CHASSIS ENVIRONMENTAL SCREEN Chassis Power Redundancy Read-OnlyPower Supply #X Status Read-Only Chassis Fan Status Read-Only5.11 PORT REDIRECT FUNCTION SCREEN Displays which modules are currently set as source modules 5.11.1 Displaying the Source and Destination Entries 5.11.2 Changing Source and Destination Ports 5.12 MODULE SELECTION SCREEN Module Type Read-only5.12.1 Selecting a Module 5.13 MODULE MENU SCREEN MODULE CONFIGURATION5.14 MODULE CONFIGURATION MENU SCREEN MODULE STATISTICSNETWORK TOOLS GENERAL CONFIGURATION Figure 5-17 Module Conﬁguration Menu ScreenSWITCH CONFIGURATION ETHERNET INTERFACE CONFIGURATIONSMARTTRUNK CONFIGURATION MODULE SPECIFIC CONFIGURATION5.15 GENERAL CONFIGURATION SCREEN Default Gateway Modiﬁable IP Address ModiﬁableSubnet Mask Modiﬁable TFTP Gateway IP Addr ModiﬁableContains the maximum number of minutes that the Local Management application displays a module’s screen while awaiting input or action from a user. For example, if the number 5 is entered in this ﬁeld, the user has up to ﬁve minutes to respond to each of the speciﬁed module’s Local Management screens. In this example, after ﬁve minutes of “idleness” no input or action, the terminal “beeps” ﬁve times, the Local Management application terminates the session, and the display returns to the Password screen. To enter a new lockout time, refer to Section This ﬁeld toggles between DISTRIBUTED and STAND ALONE 5.15.1 Setting the IP Address Clear NVRAM ToggleIP Fragmentation Toggle 5.15.2 Setting the Subnet Mask 5.15.3 Setting the Default Gateway 5.15.4 Setting the TFTP Gateway IP Address5.15.5 Setting the Module Date 5.15.6 Setting the Module Time 5.15.7 Entering a New Screen Refresh Time5.15.8 Setting the Screen Lockout Time 5.15.9 Setting the Operational Mode5.15.10 Setting the Management Mode 802.1D SWITCHING, 802.1Q SWITCHING, or SECURE FAST VLAN5.15.11 Conﬁguring the COM Port 3. Use the arrow keys to highlight YES. Press ENTER 5.15.12 Changing the Com Port Application 5.15.13 Clearing NVRAM 5.15.14 Enabling/Disabling IP Fragmentation 5.16 SNMP COMMUNITY NAMES SCREENaccess to security-protected ﬁelds of read-write Figure 5-22 SNMP Community Names Screen5.16.1 Establishing Community Names 5.17 SNMP TRAPS SCREEN Figure 5-23 SNMP Traps Screen5.17.1 Conﬁguring the Trap Table 5.18 SWITCH CONFIGURATION SCREEN The following describe each ﬁeld of the Switch Conﬁguration screen 5.18.1 Setting the STA 5.18.2 Setting the Age Time 5.18.3 Setting Enabling or Disabling the Port Status5.19 ETHERNET INTERFACE CONFIGURATION Current Oper. Mode Read-only Desired Oper. Mode SelectableLink Status Read-Only 5.19.2 Setting the FE-100TX Operational Mode 5.19.1 Conﬁguring an FE-100TX Interface5.19.3 Setting the FE-100TX Advertised Ability 5.19.5 Setting the FE-100FX and FE-100F3 in Operational Mode 5.19.4 Conﬁguring an FE-100FX or FE-100F3 Interface for Port 7 or5.20 MODULE SPECIFIC CONFIGURATION MENU SCREEN PORT REDIRECT FUNCTIONFigure 5-26 Module Speciﬁc Conﬁguration Menu Screen The Broadcast Suppression screen allows the user to set a desired limit of receive broadcast frames per port per second. For details, refer to Section 5.21 SYSTEM RESOURCES SCREEN 5.21.1 Setting the Reset Peak Utilization DRAM Installed Read-onlyNVRAM Installed Read-only Current Switch Utilization Read-only5.22 FLASH DOWNLOAD SCREEN Figure 5-28 Flash Download ScreenThe following brieﬂy explains each ﬁeld of the Flash Download screen 5.22.1 Image File Download Using TFTP 5.22.2 Image File Download Using RUNTIME 5.22.3 Image File Download Using BootP 5.23 PORT REDIRECT FUNCTION SCREENFigure 5-29 Port Redirect Function Screen 5.23.1 Changing Source and Destination Ports 5.24 BROADCAST SUPPRESSION SCREEN Figure 5-30 Broadcast Suppression Screen5.24.1 Setting the Threshold Reset Peak ToggleTime Since Peak Read-Only 5.24.2 Setting the Reset Peak Switch 5.25 MODULE STATISTICS MENU SCREENSWITCH STATISTICS The Module Statistics Menu screen displays the following menu items 5.26 SWITCH STATISTICS SCREEN Figure 5-32 Switch Statistics Screen5.26.1 Using the Clear Counters Command 5.27 THE INTERFACE STATISTICS SCREEN Interface Read-onlyInErrors Read-only Name Read-onlyInOctets Read-only InUnicast Read-onlyOutErrors Read-only Admin Status Read-onlyOutNonUnicast Read-only OutDiscards Read-only5.27.2 Using the Clear Counters Command 5.27.1 Displaying Interface Statistics5.28 RMON STATISTICS SCREEN Figure 5-34 RMON Statistics ScreenThis ﬁeld displays the name of the entity that conﬁgured this entry CRC Align Errors Read-only Multicasts Read-onlyUndersized Pkts Read-only Oversized Pkts Read-onlyIndex XX Command CLEAR COUNTERS CommandTotal Octets Read-only 64 Octets Read-only5.28.2 Using the Clear Counters Command 5.28.1 Displaying RMON Statistics5.29 NETWORK TOOLS 5.29.1 Built-in Commands commandSyntax Description1 - Other 2 - Invalid entry cannot ping device, timed out, etc OptionsExample bridge ENABLE/DISABLE IFNUM/ALL SyntaxDescription Optionsset or delete the default IP route to a managed defroute interface number IP addressdevice through the speciﬁed interface Not ApplicableSyntax DescriptionOptions ExampleSyntaxreset resetreset OptionsSyntax DescriptionOptions ExampleSyntax DescriptionOptions ExampleSyntax telnet IP address Port #Description Options5.29.2 Special Commands linktrapSyntax DescriptionAPPENDIX A SPECIFICATIONS A.1 DEVICE SPECIFICATIONSA.2 PHYSICAL PROPERTIES A.3 ENVIRONMENTAL REQUIREMENTSA.4 INPUT/OUTPUT PORTS A.5 COM PORT PINOUT ASSIGNMENTSA.6 REGULATORY COMPLIANCE SafetyElectromagnetic Compatibility EMC Appendix A Speciﬁcations 6H122-08 User’s GuideAPPENDIX B FE-100TX, FE-100FX AND FE-100F3 SPECIFICATIONS B.1 FE-100TXB.2 FE-100FX Appendix B FE-100TX, FE-100FX and FE-100F3 Speciﬁcations6H122-08 User’s Guide B.3 FE-100F3 FE-100F36H122-08 User’s Guide FE-100F3Appendix B FE-100TX, FE-100FX and FE-100F3 Speciﬁcations 6H122-08 User’s GuideAPPENDIX C OPTIONAL INSTALLATIONS AND MODE SWITCH BANK SETTINGS C.2 SETTING THE MODE SWITCHC.1 REQUIRED TOOLS Switch deﬁnitions and positions are as follows Switch 7 - Clear NVRAM. Changing the position of this switch resets NVRAM on the next power up. ALL user entered parameters, such as IP addresses, subnet masks, SNMP traps, and switching functions are restored to their factory default settings C.3 INSTALLING OPTIONAL FAST ETHERNET INTERFACE MODULES Appendix C Optional Installations and Mode Switch Bank SettingsFigure C-2 6H122-08 Fast Ethernet Interface Module Connector Location Optional Fast Ethernet Interface Modules ConnectorsTo install a Fast Ethernet Interface Module in port slot 7 or 8 of the 2. Remove the screw from the rear standoff. Save the screw 7. Installation is complete Appendix C Optional Installations and Mode Switch Bank Settings 6H122-08 User’s GuideINDEX Numerics6H122-08 User’s Guide Index-1Index Index-26H122-08 User’s Guide Index 6H122-08 User’s GuideIndex-3 Index Index-46H122-08 User’s Guide