Carrier PCV015-060 APPENDIX A - WSHP SCREEN OPEN CONFIGURATION cont, Indoor Air Quality

APPENDIX A — WSHP SCREEN OPEN CONFIGURATION (cont)

SCREEN NAME		POINT NAME	PASSWORD	EDITABLE	RANGE	DEFAULT	NOTES
			LEVEL
							Defines the hysteresis applied above
		SPT Occupied Alarm		X	2 - 20 ° F	5 ° F	the cooling and below the heating set
		Hysteresis					points before an alarm condition will
							occur
							Used to calculate the delay time before
		SPT Alarm Delay		X	0 - 30 min per degree	10 min	an alarm is generated after the alarm
							condition occurs
		SPT Unoccupied Low		X	35 - 90 ° F	45 ° F	Defines the fixed unoccupied
		Alarm Temperature					ow SPT alarm limit
		SPT Unoccupied High		X	45 - 100 ° F	95 ° F	Defines the fixed unoccupied
		Alarm Temperature					high SPT alarm limit
		SAT Low SAT		X	15 - 90 ° F	45 ° F	Defines the fixed minimum
		Alarm Limit					SAT alarm limit
		SAT High SAT		X	90 - 175 ° F	120 ° F	Defines the fixed maximum
		Alarm Limit					SAT alarm limit
		Condensate Overflow					Defines the delay time before an alarm
				X	5 - 600 sec	10 sec	is generated after the alarm condition
		Alarm Delay
							occurs
		Space Humidity Occupied		X	45% - 100%	100%	Defines the fixed occupied
		High Alarm Limit					high space RH alarm limit
		Space Humidity Alarm					Used to calculate the delay time before
Configuration				X	0 - 30 min per % RH	5 min	an alarm is generated after the alarm
		Delay
							condition occurs
	→	Space Humidity Unoccu-	Admin Password	X	45% - 100%	100%	Defines the fixed unnoccupied
		pied High Alarm Limit	level access only				high space RH alarm limit
	Alarm	IAQ/Ventilation Occupied		X	0 - 9999 ppm	1100 ppm	Defines the fixed occupied high
Configuration		High Alarm Limit					space IAQ/Ventilation alarm limit
		IAQ/Ventilation					Used to calculate the delay time before
				X	0.1 - 1.0 min per ppm	0.25 min	an alarm is generated after the alarm
		Alarm Delay
							condition occurs
		Rnet Sensor SPT Alarm		X	Ignore/Display	Ignore	Determines if the SPT alarm is
							displayed on the local Rnet sensor
		Rnet Sensor SAT Alarm		X	Ignore/Display	Ignore	Determines if the SAT alarm is
							displayed on the local Rnet sensor
		Rnet Sensor Compressor					Determines if the Compressor Lockout
				X	Ignore/Display	Display	alarm is displayed on the local Rnet
		Lockout Alarm
							sensor
		Rnet Sensor Condenser					Determines if the Condenser Water
				X	Ignore/Display	Display	Temperature alarm is displayed on the
		Water Temperature Alarm
							local Rnet sensor
		Rnet Sensor Condensate					Determines if the Condensate
				X	Ignore/Display	Display	Overflow alarm is displayed on the
		Overflow Alarm
							local Rnet sensor
		Rnet Sensor Dirty		X	Ignore/Display	Display	Determines if the Dirty Filter alarm is
		Filter Alarm					displayed on the local Rnet sensor
		Rnet Sensor Space					Determines if the High Space
				X	Ignore/Display	Ignore	RH alarm is displayed on the
		High Humidity Alarm
							local Rnet sensor
Configuration		Loop Control Network					See TPI
		Number
	→	Loop Control Network					See TPI
		Address
Linkage		Number of Linked Heat					See TPI
		Pumps
	LEGEND
BAS — Building Automation System
DCV	— Demand Controlled Ventilation
IAQ	— Indoor Air Quality
OAT	— Outdoor Air Temperature
RH	— Relative Humidity
SAT — Supply Air Temperature
SPT	— Space Temperature
TPI	— Third Party Integration

48