Manuals / CH Tech / Computer Equipment / Network Router

CH Tech EM405D user manual Applicable Documents, IEEE-802.3 ANSI 8802.3, Ethernet Network Standard

Models: EM405D

1 48

Page 10

1.7 APPLICABLE DOCUMENTS

ANSI/VITA 12-1996 American National Standard for The Mezzanine Concept M- Module Specification, Approved May 20, 1997, VMEbus International Trade Association, 7825 E. Gelding Dr. Suite 104, Scottsdale, AZ 85260-3415, E-mail: info@vita.com, www.vita.com

IEEE-802.3 (ANSI 8802.3), Ethernet Network Standard

IEEE-802.11b, Wireless Ethernet Standard

Page 10

Image 10

CH Tech EM405D user manual Applicable Documents, IEEE-802.3 ANSI 8802.3, Ethernet Network Standard

Contents

M O D E L E M 4 0 5 D U S E R S M A N U A L E T H E R N E T M - M O D U L E C A R R I E RManual Part No COPYRIGHT Copyright 2004 by C&H Technologies, IncDOCUMENT REVISION NOTICE INTRODUCTION GENERAL DESCRIPTION TABLE OF CONTENTSINSTALLATION FUNCTIONAL DESCRIPTIONAPPENDIX C - WIRELESS ETHERNET WI-FI DEFAULT SETTINGS APPENDIX A - CONNECTORSAPPENDIX B - WIRED ETHERNET DEFAULT SETTINGS LIST OF FIGURES1.0 GENERAL DESCRIPTION 1.2 FEATURES AND SPECIFICATIONS 1.2.1 Key FeaturesFigure 1. EM405D Ethernet M-Module Carrier 1.1 PURPOSE OF EQUIPMENT MAXIMUM RATINGS 1.2.2 SpecificationsCHARACTERISTICS Parameter1.5 Environmental 1.3 Electrical1.4 Mechanical 1.6 Bus ComplianceIEEE-802.11b, Wireless Ethernet Standard 1.7 APPLICABLE DOCUMENTSIEEE-802.3 ANSI 8802.3, Ethernet Network Standard 2.3 INSTALLATION OF M-MODULES 2.0 INSTALLATION 2.1 UNPACKING AND INSPECTION2.2 HANDLING PRECAUTIONS Figure 2. M-module InstallationMODULE B Figure 3. M/MA Configuration DiagramMODULE A 3.1.2 Ethernet Interface Figure 4. Functional Block Diagram 3.1.1 Embedded Controller3.0 FUNCTIONAL DESCRIPTION 3.1 GENERAL ETHERNET3.2 REAR PANEL 3.1.4 Power Conversion3.1.3 M-module Interface Figure 5. Rear PanelFigure 6. Front Panel 3.3 FRONT PANELEM405D ETHERNET M-MODULE CARRIER Page 4.0 OPERATING INSTRUCTIONS 4.1 GENERAL 4.2 CONFIGURING THE ETHERNET INTERFACE4.2.1 IP Address The default port number for standard module access is The default subnet mask is 4.2.3 GatewayThe default gateway address is 4.2.4 Port Numbers 4.2.5 Wireless SettingsThe default settings are WEP disabled and WPA disabled The default setting is Auto-Scan4.2.6 Performing the Configuration - Wired Ethernet telnet x.x.x.x 4.2.7 Performing the Configuration - Wireless Ethernet Wi-Fi 4.2.7.1 Wed-based Configuration 4.3 COMMUNICATING WITH THE CARRIER AND M-MODULES Table I. Command Summary4.3.1 Error Handling Table II. Status Code SCSuccessful 0x00 The command completed successfully without error 4.3.2 Write Data command 4.3.3 Read Data command4.3.4 Block Access 4.3.4.1 Block Write command 4.3.4.2 Block Read command Offset 4.3.5 EM405D Configuration/Status RegistersTable III. Register Summary RegisterHardware Version Reset Error & Manufacturer IdentificationDevice Identification Firmware VersionFigure 7. EM405D Registers continued Reset & Trigger ControlFan Control & Temperature Status  Module A Trigger B Direction 0 = input, 1 = output4.4 CONTROLLING THE TRIGGERS 4.5 FAN AND TEMPERATURE CONTROL C = TEMP - 281Page PIN DESCRIPTION 1 +12V INPUT 2 +12V INPUT 3 +12V INPUT 4 TRIGGER OUT Figure A-1. 9-Pin DSUB Connector5 TRIGGER IN 6 GND 7 GND 8 GND 9 GND Page Table B-1. Ethernet Interface Default Settings Table B-1. Ethernet Interface Default Settings. continued Email Notification Table B-1. Ethernet Interface Default Settings. continuedOEM Configurable Pins blankPage Wireless LAN Settings Table C-1. Wireless Ethernet Configuration Default SettingsIP Settings Wireless Security SettingsTCP Server Settings Advanced Network SettingsPort Profile Settings TCP Client Settingsblank blankblank Page N O T E S Page READERS COMMENT FORM INSTRUCTIONS