Manuals / CH Tech / Computer Equipment / Network Router

CH Tech EM405D Table B-1. Ethernet Interface Default Settings. continued, Email Notification

Models: EM405D

1 48

Page 39

Table B-1. Ethernet Interface Default Settings. (continued)

Email Notification
Domain Name	blank
Mail Server	0.0.0.0
Recipients	(Collection)
Triggers	(Collection)
Unit Name	blank

Host List
Host List	(Collection)
Retry Counter	3
Retry Timeout	250

OEM Configurable Pins
Pin 1	IN1
Pin 2	IN2
Pin 3	IN3
User IO	ActiveLow

XPort-03
CPU Performance	High

B-3

Page 39

Image 39

CH Tech EM405D Table B-1. Ethernet Interface Default Settings. continued, Email Notification, blank, Host List, XPort-03

Contents

U S E R S M A N U A L E T H E R N E T M - M O D U L E C A R R I E R M O D E L E M 4 0 5 DManual Part No Copyright 2004 by C&H Technologies, Inc COPYRIGHTDOCUMENT REVISION NOTICE INTRODUCTION FUNCTIONAL DESCRIPTION TABLE OF CONTENTSINSTALLATION GENERAL DESCRIPTIONLIST OF FIGURES APPENDIX A - CONNECTORSAPPENDIX B - WIRED ETHERNET DEFAULT SETTINGS APPENDIX C - WIRELESS ETHERNET WI-FI DEFAULT SETTINGS1.2 FEATURES AND SPECIFICATIONS 1.2.1 Key Features 1.0 GENERAL DESCRIPTIONFigure 1. EM405D Ethernet M-Module Carrier 1.1 PURPOSE OF EQUIPMENT Parameter 1.2.2 SpecificationsCHARACTERISTICS MAXIMUM RATINGS1.6 Bus Compliance 1.3 Electrical1.4 Mechanical 1.5 Environmental1.7 APPLICABLE DOCUMENTS IEEE-802.11b, Wireless Ethernet StandardIEEE-802.3 ANSI 8802.3, Ethernet Network Standard Figure 2. M-module Installation 2.0 INSTALLATION 2.1 UNPACKING AND INSPECTION2.2 HANDLING PRECAUTIONS 2.3 INSTALLATION OF M-MODULESFigure 3. M/MA Configuration Diagram MODULE BMODULE A ETHERNET Figure 4. Functional Block Diagram 3.1.1 Embedded Controller3.0 FUNCTIONAL DESCRIPTION 3.1 GENERAL 3.1.2 Ethernet InterfaceFigure 5. Rear Panel 3.1.4 Power Conversion3.1.3 M-module Interface 3.2 REAR PANEL3.3 FRONT PANEL Figure 6. Front PanelEM405D ETHERNET M-MODULE CARRIER Page 4.2 CONFIGURING THE ETHERNET INTERFACE 4.0 OPERATING INSTRUCTIONS 4.1 GENERAL4.2.1 IP Address 4.2.5 Wireless Settings The default subnet mask is 4.2.3 GatewayThe default gateway address is 4.2.4 Port Numbers The default port number for standard module access isThe default setting is Auto-Scan The default settings are WEP disabled and WPA disabled4.2.6 Performing the Configuration - Wired Ethernet telnet x.x.x.x 4.2.7 Performing the Configuration - Wireless Ethernet Wi-Fi 4.2.7.1 Wed-based Configuration Table II. Status Code SC Table I. Command Summary4.3.1 Error Handling 4.3 COMMUNICATING WITH THE CARRIER AND M-MODULESSuccessful 0x00 The command completed successfully without error 4.3.3 Read Data command 4.3.2 Write Data command4.3.4 Block Access 4.3.4.1 Block Write command 4.3.4.2 Block Read command Register 4.3.5 EM405D Configuration/Status RegistersTable III. Register Summary OffsetFirmware Version Reset Error & Manufacturer IdentificationDevice Identification Hardware Version Enclosure Temperature C = TEMP - 281 Reset & Trigger ControlFan Control & Temperature Status Figure 7. EM405D Registers continued4.4 CONTROLLING THE TRIGGERS C = TEMP - 281 4.5 FAN AND TEMPERATURE CONTROLPage Figure A-1. 9-Pin DSUB Connector PIN DESCRIPTION 1 +12V INPUT 2 +12V INPUT 3 +12V INPUT 4 TRIGGER OUT5 TRIGGER IN 6 GND 7 GND 8 GND 9 GND Page Table B-1. Ethernet Interface Default Settings Table B-1. Ethernet Interface Default Settings. continued blank Table B-1. Ethernet Interface Default Settings. continuedOEM Configurable Pins Email NotificationPage Wireless Security Settings Table C-1. Wireless Ethernet Configuration Default SettingsIP Settings Wireless LAN SettingsTCP Client Settings Advanced Network SettingsPort Profile Settings TCP Server Settingsblank blankblank Page N O T E S Page READERS COMMENT FORM INSTRUCTIONS

Email Notification

blank

Host List

OEM Configurable Pins

XPort-03