Manuals / CH Tech / Computer Equipment / Network Router

CH Tech EM405D user manual Electrical, Mechanical, Environmental, Bus Compliance

Models: EM405D

1 48

Download 48 pages 8.75 Kb

Page 9

1.3 Electrical

The EM405D only requires a +12V DC power input. The +12V input is internally converted to the +3.3V power required by the carrier and the +5V, +12V, and -12V power required by the M- modules. A maximum of 30 watts is required to support the carrier and two M-modules operating at the maximum allowed power consumption. The maximum allowed power consumption for each M-module is 1A of +5V and 200ma each of +12V and -12V. The EM405D uses power-off resetable fuses on the incoming +12V supply. If a fault occurs, power must be removed before the fuse will reset. The fuse is rated at 5 amps.

1.4 Mechanical

The EM405D is contained in a metal chassis with an outside dimension of 5.6 inches wide by 8.5 inches deep by 1.5 inches high. A variable speed fan provides forced air for cooling the M- modules. The unit weighs approximately 1.7 lbs with no M-modules installed.

1.5 Environmental

The environmental specifications of the module are:

Operating Temperature:	0°C to +60°C*
Storage Temperature:	-40°C to +75°C
Humidity:	<95% without condensation

*The forced air cooling is designed to allow a maximum 20°C temperature rise for installed M- modules. In other words, with two M-modules operating at full dissipation, the M-modules’ temperature can only be maintained within 20°C of the ambient air inlet temperature.

Installed M/MAs may differ in environmental specification. Refer to each individual M/MA’s documentation for information.

1.6 Bus Compliance

The module complies with the ANSI/VITA 12-1996 Specification for single or double-wide M- Modules and the MA-Module trigger signal extension.

Addressing:	A08 only (extended addressing not supported)
Data:	D16 only
Interrupts:	not supported
DMA:	not supported
Triggers:	Trig A and Trig B Input/Output
Manufacturer ID:	0FC116
Model Number:	0FDB16

3

Image 9

CH Tech EM405D user manual Electrical, Mechanical, Environmental, Bus Compliance

Contents

U S E R S M A N U A L E T H E R N E T M - M O D U L E C A R R I E R M O D E L E M 4 0 5 DManual Part No Copyright 2004 by C&H Technologies, Inc COPYRIGHTDOCUMENT REVISION NOTICE INTRODUCTION INSTALLATION TABLE OF CONTENTSGENERAL DESCRIPTION FUNCTIONAL DESCRIPTIONAPPENDIX B - WIRED ETHERNET DEFAULT SETTINGS APPENDIX A - CONNECTORSAPPENDIX C - WIRELESS ETHERNET WI-FI DEFAULT SETTINGS LIST OF FIGURES1.2 FEATURES AND SPECIFICATIONS 1.2.1 Key Features 1.0 GENERAL DESCRIPTIONFigure 1. EM405D Ethernet M-Module Carrier 1.1 PURPOSE OF EQUIPMENT CHARACTERISTICS 1.2.2 SpecificationsMAXIMUM RATINGS Parameter1.4 Mechanical 1.3 Electrical1.5 Environmental 1.6 Bus Compliance1.7 APPLICABLE DOCUMENTS IEEE-802.11b, Wireless Ethernet StandardIEEE-802.3 ANSI 8802.3, Ethernet Network Standard 2.2 HANDLING PRECAUTIONS 2.0 INSTALLATION 2.1 UNPACKING AND INSPECTION2.3 INSTALLATION OF M-MODULES Figure 2. M-module InstallationFigure 3. M/MA Configuration Diagram MODULE BMODULE A 3.0 FUNCTIONAL DESCRIPTION 3.1 GENERAL Figure 4. Functional Block Diagram 3.1.1 Embedded Controller3.1.2 Ethernet Interface ETHERNET3.1.3 M-module Interface 3.1.4 Power Conversion3.2 REAR PANEL Figure 5. Rear Panel3.3 FRONT PANEL Figure 6. Front PanelEM405D ETHERNET M-MODULE CARRIER Page 4.2 CONFIGURING THE ETHERNET INTERFACE 4.0 OPERATING INSTRUCTIONS 4.1 GENERAL4.2.1 IP Address The default gateway address is 4.2.4 Port Numbers The default subnet mask is 4.2.3 GatewayThe default port number for standard module access is 4.2.5 Wireless SettingsThe default setting is Auto-Scan The default settings are WEP disabled and WPA disabled4.2.6 Performing the Configuration - Wired Ethernet telnet x.x.x.x 4.2.7 Performing the Configuration - Wireless Ethernet Wi-Fi 4.2.7.1 Wed-based Configuration 4.3.1 Error Handling Table I. Command Summary4.3 COMMUNICATING WITH THE CARRIER AND M-MODULES Table II. Status Code SCSuccessful 0x00 The command completed successfully without error 4.3.3 Read Data command 4.3.2 Write Data command4.3.4 Block Access 4.3.4.1 Block Write command 4.3.4.2 Block Read command Table III. Register Summary 4.3.5 EM405D Configuration/Status RegistersOffset RegisterDevice Identification Reset Error & Manufacturer IdentificationHardware Version Firmware VersionFan Control & Temperature Status Reset & Trigger ControlFigure 7. EM405D Registers continued  Enclosure Temperature C = TEMP - 2814.4 CONTROLLING THE TRIGGERS C = TEMP - 281 4.5 FAN AND TEMPERATURE CONTROLPage Figure A-1. 9-Pin DSUB Connector PIN DESCRIPTION 1 +12V INPUT 2 +12V INPUT 3 +12V INPUT 4 TRIGGER OUT5 TRIGGER IN 6 GND 7 GND 8 GND 9 GND Page Table B-1. Ethernet Interface Default Settings Table B-1. Ethernet Interface Default Settings. continued OEM Configurable Pins Table B-1. Ethernet Interface Default Settings. continuedEmail Notification blankPage IP Settings Table C-1. Wireless Ethernet Configuration Default SettingsWireless LAN Settings Wireless Security SettingsPort Profile Settings Advanced Network SettingsTCP Server Settings TCP Client Settingsblank blankblank Page N O T E S Page READERS COMMENT FORM INSTRUCTIONS