Manuals / CH Tech / Computer Equipment / Network Router

CH Tech EM405D user manual U S E R S M A N U A L E T H E R N E T M - M O D U L E C A R R I E R

Models: EM405D

1 48

Download 48 pages 8.75 Kb

Page 1

U S E R ' S M A N U A L

E T H E R N E T

M - M O D U L E

C A R R I E R

M O D E L

E M 4 0 5 D

Manual Part No: 11028854

Image 1

CH Tech EM405D user manual U S E R S M A N U A L E T H E R N E T M - M O D U L E C A R R I E R, M O D E L E M 4 0 5 D

Contents

M O D E L E M 4 0 5 D U S E R S M A N U A L E T H E R N E T M - M O D U L E C A R R I E RManual Part No Copyright 2004 by C&H Technologies, Inc COPYRIGHTDOCUMENT REVISION NOTICE INTRODUCTION INSTALLATION TABLE OF CONTENTSGENERAL DESCRIPTION FUNCTIONAL DESCRIPTIONAPPENDIX B - WIRED ETHERNET DEFAULT SETTINGS APPENDIX A - CONNECTORSAPPENDIX C - WIRELESS ETHERNET WI-FI DEFAULT SETTINGS LIST OF FIGURES1.0 GENERAL DESCRIPTION 1.2 FEATURES AND SPECIFICATIONS 1.2.1 Key FeaturesFigure 1. EM405D Ethernet M-Module Carrier 1.1 PURPOSE OF EQUIPMENT CHARACTERISTICS 1.2.2 SpecificationsMAXIMUM RATINGS Parameter1.4 Mechanical 1.3 Electrical1.5 Environmental 1.6 Bus ComplianceIEEE-802.11b, Wireless Ethernet Standard 1.7 APPLICABLE DOCUMENTSIEEE-802.3 ANSI 8802.3, Ethernet Network Standard 2.2 HANDLING PRECAUTIONS 2.0 INSTALLATION 2.1 UNPACKING AND INSPECTION2.3 INSTALLATION OF M-MODULES Figure 2. M-module InstallationMODULE B Figure 3. M/MA Configuration DiagramMODULE A 3.0 FUNCTIONAL DESCRIPTION 3.1 GENERAL Figure 4. Functional Block Diagram 3.1.1 Embedded Controller3.1.2 Ethernet Interface ETHERNET3.1.3 M-module Interface 3.1.4 Power Conversion3.2 REAR PANEL Figure 5. Rear PanelFigure 6. Front Panel 3.3 FRONT PANELEM405D ETHERNET M-MODULE CARRIER Page 4.0 OPERATING INSTRUCTIONS 4.1 GENERAL 4.2 CONFIGURING THE ETHERNET INTERFACE4.2.1 IP Address The default gateway address is 4.2.4 Port Numbers The default subnet mask is 4.2.3 GatewayThe default port number for standard module access is 4.2.5 Wireless SettingsThe default settings are WEP disabled and WPA disabled The default setting is Auto-Scan4.2.6 Performing the Configuration - Wired Ethernet telnet x.x.x.x 4.2.7 Performing the Configuration - Wireless Ethernet Wi-Fi 4.2.7.1 Wed-based Configuration 4.3.1 Error Handling Table I. Command Summary4.3 COMMUNICATING WITH THE CARRIER AND M-MODULES Table II. Status Code SCSuccessful 0x00 The command completed successfully without error 4.3.3 Read Data command 4.3.2 Write Data command4.3.4 Block Access 4.3.4.1 Block Write command 4.3.4.2 Block Read command Table III. Register Summary 4.3.5 EM405D Configuration/Status RegistersOffset RegisterDevice Identification Reset Error & Manufacturer IdentificationHardware Version Firmware VersionFan Control & Temperature Status Reset & Trigger ControlFigure 7. EM405D Registers continued  Enclosure Temperature C = TEMP - 2814.4 CONTROLLING THE TRIGGERS C = TEMP - 281 4.5 FAN AND TEMPERATURE CONTROLPage PIN DESCRIPTION 1 +12V INPUT 2 +12V INPUT 3 +12V INPUT 4 TRIGGER OUT Figure A-1. 9-Pin DSUB Connector5 TRIGGER IN 6 GND 7 GND 8 GND 9 GND Page Table B-1. Ethernet Interface Default Settings Table B-1. Ethernet Interface Default Settings. continued OEM Configurable Pins Table B-1. Ethernet Interface Default Settings. continuedEmail Notification blankPage IP Settings Table C-1. Wireless Ethernet Configuration Default SettingsWireless LAN Settings Wireless Security SettingsPort Profile Settings Advanced Network SettingsTCP Server Settings TCP Client Settingsblank blankblank Page N O T E S Page READERS COMMENT FORM INSTRUCTIONS